AOES3030SS-P113237NSS Amana Wall Oven - Instructions

This is a very easy repair as the sensor had 2 screws and slid out of the back of the inside of the oven just enough to hook up the new one. I never had to back the oven out of the wall. It is a 5 minute repair. Ok I did use my son's head lamp from scouts for better light as you have to kill the power to the oven, so no oven light. And you can't hold a flashlight and do this alone.

However, I ordered the part before I took the old part out. Don't do that. There are 2 froms of Temp sensors that you can order one male and one female. I did not know that and just ordered what looked to be the right part. It turned out that I needed the female sensor. When I called the folks at part select they were terrific! They sent out the new part the next day and a UPS form via email to send the other part back.

I don't know what a service call would have been but this was very easy. I will go here first for appliance parts. Women can fix stuff too!

Purchased 2 piece broiler pan from this site

First I removed the screws that hold the element in place. Then I removed the screws that hold the element shield on the top of oven in place. I then pulled the element out of the back of the oven about 3-4 inches and disconnected the two wires. I removed the whole assembly shield and element. Then I disconnected the element from the shield little brackets hold it in place. Took new element and fixed in place on the shield with the brackets. At this point I replaced the two screws that hold the element to oven shield. Then I took the whole assembly and reconnected the two wires. Pushed the element back into the back of the oven. Lined up the screw holes of oven and broiler shield put screws back in. And done. I might add I turned the power off to the oven before working on it.

First, turn off power to oven. There are six Phillips head screws on the pan above the element and 2 securing the element to the pan. Remove all screws and pull unit toward you, then slide off electrical wires from the element. To remove the element from the pan use the pliers to bend back metal hooks. Place new element under hooks, bending the metal to hold element in place and replace 2 screws securing the element to the pan. Join wires to element and push unit with wiring back into oven wall. Replace 6 screws holding pan to top of oven, turn on power, and voila!

I took out ruined racks. Cleaned the oven, getting rid of all the melted plastic. Once oven was sparkling clean, I slid in the new racks I bought from here. (The easiest part).

* * * *
I'm very thankful to have found this site. My oven has been "out of order" for over 3 years. It's so nice to be able to use it again! =)

I called the local appliance parts store and they said it would cost $60-80 and take a week to order. I paid $16 and received my rack in 2 days!

I just ordered a new wire oven rack from you. When it came all I had to do was to remove it from the carton it came in and place it in the oven. It fit perfectly. Thanks

Although this was not a repair I wanted to let you know your service was outstanding and the price quite reasonable. I am very happy to finally have a much needed second rack in my oven that was not there when I purchased my home. Thank You

The repair WOULD have been very easy except one of the wires did not come out with the broiler unit, thus the entire oven had to be removed from the cabinet, then had to be rethreaded into broiler area. Be very careful when taking out the old broiler to be sure that both wires come out with it.

I ordered new racks to see if they weere out of alignment. The new racks fell from its tracks after the broiler was heated. It seems the oven cabinet is expanding with the heat and the rack width does not compensate for that. The new racks did not solve the problem so I do not know what can be done next. Any shelf support would have to be heat resistent. Replacing the oven cabinet is not a good option and no gauantee it wouldn't continue with this stove.

I just replaced the racks with beautiful, new, shiny racks. My wife was very pleased

Bought a new one. . Three years later =)

Loosen 6 screws holding pan containing element.Pull element and pan towards the front of oven.Remove the 2 wires attached to element.Remove 2 screws holding element to pan.(Needed WD 40 to loosen screws).Replace in reverse order.So simple this caveman could do it!

Very simple process of just ensuring you have the correct size racks and remove the old racks and replace them with the new ones.
Having ordered a lot of things on the internet, I am very pleased with using Part select and would "highly" recommend them to all!!

ordered new broiler pan