AN01A Admiral Refrigerator - Instructions

Removed the old fan; cut the wire and spliced in the new fan and reassembled. A little over one hour. Refrig is working perfectly now with lower settings. It is definitely off much more than on now.

just had to remove the fan motor the hard thing is getting down to it

I folded in half twice! and took the back off the fridge(cardboard) and took one brace off and just took the screws off the fan from the other two braces. Turned the fan enough to get at the wires for the fan and cut them off an inch from the old fan, stripped the insulation and wire nutted them to new fan. Make sure they don't interfere with the new fan and put the new fan in place put the screws in and we're making ice and cold fridge again.

I removed the cover that protects the freezing tubes, they were frozen solid,used my heat gun to melt away the ice, being very careful not to burn any wires. Then I removed the old heating coils,connected the new ones, replaced the cover and I was done. The thing that took the most time was melting the ice, you cant do it in a hurry because you may burn wires

Pull box out ""unplug box"" empty frezer including storage baskets,place ice maker in off remove ice cube box, do not remove ice maker, useing nut driver loosen side rail screws about 1/4"slide basket rails in or out and pull to center of box should slip off screws, remove light bulb cover & bulb, remove 4 screws holding ice worm drive motor "" hold "" will fall it is atached to a electrial plug un plug and lay aside,unscrew back panle screws 4 left 4 right on back cover, " remove hiden screw at top center of back panel and pull up and pry out at bottom silde out downwerds,remove cross plates one center one bottom these hold defoster bars, unwind wires center defroster bar somewhat difecult bottom one just slide down unplug from panel at top behind where ice cube drive was located, replace new defroster assm reasemble defroster bars into cross bars wind in & plug up new wires behind cooling fins being carefule not to cut or nick wires of bend cooling fins replace screws,wires are 1 small plug 1 large,reinstall back panle top center screw first don't tighten aline side screw holes replace side screws then tighten top screw. Replace drive motor being sure to conect,replace bulb,bulb cover,side railes,bens,ice cube box & put ice maker lever in on poss. Plug box in weight 8 to 10 hours with box set at mfg 's starting settings. Should work like a charm.

It wasn't quite as easy to get to the bolts as the video showed. The lay out of the part wasn't exactly like the video either. However, I managed to put the new part in. Unfortunately, it didn't solve the problem. At first the fridge cycled on and off but after 12 hrs it started to freeze liquids again. Since the appliance was 17 years old we opted to just get a new one.

Well I could what laid on the floor and replaced it but I didn't I emptied refrigerator laid it over change the motor then stood it back up actual work about three hours

The video of the repair is a helpful guide, but my refrigerator has the compressor very close to the condenser fan motor. With the compressor comes the copper tubing that is all in the way. I had to carefully bend them now and then to allow me to get my hands in position. The how to is easy, but the working with tools in cramped quarters was difficult. I think my Maytag side by side model makes for this job to be difficult, maybe yours may not be so bad. I took a couple of hours to complete. After the first hour, I covered the bare wires, and plugged the frig back in so it could do some cooling. I placed a small in front on the condenser to blow across it. Had a little break, then finished the job.

removed condenser fan -located behind refrigerator next to compressor, Not much clearance to work, there are 3 screws to remove from condensing motor,sounds easy but clearance is lacking to remove them ,(takes alot of PATIENCE). Then you have to remove the fan blades to be able to get clearance to remove motor!! I wouldn't reccommend trying this repair unless you are a pro.