This gas dryer ignition coil set comes with two ignition coils: one three-terminal boost/hold coil, and one two terminal secondary coil. Usually only one of them burns out but you should replace them ...
If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found both on the idler pul...
This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
The blower wheel is a squirrel cage type wheel whose purpose is to move the air through the room or appliance. The blower wheel spins on the motor shaft to blow air through the dryer drum and out through the exhaust.
This part senses the flame for heat allowing the gas valve to open.This flame sensor is three inches long and is used for many gas clothes dryers.This flame sensor assembly is made of both plastic and metal.
This silicone carbide igniter with ceramic holder kit includes the 3" flat igniter, bracket, 4" wire leads, and the plug. It can replace both round and flat igniters. This kit is used for many gas clothes dryers.
$51.69
In Stock
Questions And Answers for AGD4475TQ1
Ask our experts a question about this model and we'll get back to you as soon as possible!
4 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Leo
January 31, 2022
Dryer does not heat on "timed dry- high heat" or " auto sense dry" selection. It will only heat on "timed dry-low heat". What part do I need to fix the dryer so it works on all selections?
For model number AGD4475TQ1
Hello Leo, Thank you for the question. This is normally an indication the Timer Switch is faulty. The Timer sends power to the element during the cycles. If faulty, it may not be working in all cycles. The timer can be tested. You will want to check at the timer for power from the red to the white wire with black strip or terminals A to F for 120 vac. If there is 120 vac then the motor is the issue. If there is not 120 vac then the issue will be with the timer. We hope this helps!
Where is the thermostat located and how do you know if it’s not good
For model number AGD4475TQ1
Hello Tom, thank you for contacting us. You can test the thermostat using a multimeter. If the thermostat, part number PS11741405, does not have continuity it is faulty. The thermostat can be located by removing the back panel of the dryer. The attached video can help you locate it. We hope this helps.
Hello Nipu, thank you for your inquiry. Based on our understanding of the issue, we would suggest you replacing the thermal fuse, part number PS11741460. Good luck with the repair!
Was this helpful?
Thank you for voting!
Scott
January 20, 2024
Hi our gas dryer will heat only on timed dry high heat. no heat on any of the other settings
For model number AGD4475TQ1
Hi Scott, thank you for getting in touch. According to our research, the issue is most probably with the dryer timer, part number PS11749826. It controls the electrical components and the duration of the dryer cycles. You may need to replace it to fix the issue. We hope this solves your problem!
Pryed dryer top open and opened front door. . Unscrewed the 2 retaining screws. Pulled old switch from the wiring harness. Put new switch in place and replaced the retaining screws. Put new switch wire plug into the wiring harness. Before closing top, checked door switch function with dryer on. Dryer cut off when door open and when closed dryer started normally. . . Maint. Note instruction book should warn that letting door slam, which I did on occaision, broke the switch arm. Might save future problems.
First I shut off the gas supply and disconnected the dryer vent and unpluged the unit so you can access the rear of the dryer. Then I removed the rear cover. This is where you will find your thermostats and fuses. Holding the new part next to the one to be replaced I transfer the wires one at a time so as not to get them mixed up, then unscrew the old part and install the new one. Insert a flat blade screwdriver under the top cover in the 2 front corners to unsnap it from it's clips, also at this time you need to remove the 2 screws that hold the upper part of the lint filter tube to the lid, then lift the lid to expose the drum ( I tilted the dryer back as far as the flex gas line would allow me to and rested the top lid against the wall without removing it, to many wires). Behind the front cover in the top right corner is the plug for the door switch,un-plug it and also there are 2 screws one in each corner. After that lift the front cover straight up and pull it away from the cabinet ( it has clips at the bottom to hold it in place). Reaching under the drum on the right side pull down on the belt tensioner and release the belt from the motor then you can remove the drum. Laying the drum down on it's front edge I removed the rear felt seal and took a piece of sand paper to rough up th old glue and clean off some of the felt that was still stuck to the drum. Following the directions from the seal package I put the glue around the edge of the drum and re-installed the new felt. This is a good time to clean out your dryer, while the glue sets up. A shop vac works the best, but be carefull not to suck up the money, it will help pay for the repair ( I found over a dollar in change ). At this time I also changed the coils on the gas valve, remove the 2 screws that hold the clamp and replace them one at a time. Re-install the drum with the belt on it, fold it and push it through the tensioner and put it on the motor pulley. rotate the drum to make sure that the felt is not kinked under itself, re-install the front cover bottom clips first, then the 2 screws and the plug for the door switch, pull down the lid and snap it in place, before installing the rear cover this is a good time to remove the rear cover to the lint chute and clean in there also ( it's easy to see why there are so many dryer fires). Re- install that cover and the rear cover and vent tube, turn your gas back on and check it for leaks ( even if you didn't disconnect it) plug your dryer back in and get busy catching up on the laundry that you haven't had a chance to do because your dryer broke, then smile and think about all the money you saved by doing this simple repair your self. Thanks Parts Select