AFI2539ERB00 Amana Refrigerator - Instructions

Since it wasn't possible to squeeze the seal in between the door groove and the bar which closes the gap between the two doors, I cut the seal side in half and snaked it in from the top and the bottom. Since the cut is behind the bar when the door is closed there is no compromise in getting a good seal around the door. Note there was no apparent way to easily remove this bar.

Very easy. Just get hold of the gasket with your strong fingers and pull it out of the groove it is in. Clean the groove, I used Windex and paper towels. On the new gasket there are 2 wide areas on the vertical part. these must be facing toward you and on the handle side of the door. start at the tor center of the door and work the gasket in with your fingers outward to the corners then work on the bottom of the gasket in the same manner, then start on the vertical gaskets. when you think every thing is aligned take your thumbs and press very hard all around. You may have to repeat.

It was quit simple. I removed the draw and the shelves above the pantry unit. Once everything was removed (2min), I removed the one side pantry bracket ( 2 screw's). Put in the new pantry bracket and screw's and I was done. I'll give it ten minutes total. easy button Thank you

First, I took out the glass tray along with the two slide out compartments that are part of that assembly. Then I used a small socket set to take out the three screws that hold the part in place and along with the part a plastic connector comes out with it that adjusts the temp of the bin area. Line up the holes on the slider and two screws come out that hold the slider to the part. Disconnet the plastic piece in the back that adjusts are flow (press down plastic holders) Reattach the slider, snap the plastic piece on the back and reassemble. Sounds complicated but once you are in there, its self explanatory.

Parts delivered quick. 15-20 minute repair time. Just needed to remove a few shelves, then screws to remove damaged parts and replace with new. Very easy repair.

For this repair, the following YouTube video was most helpful in showing how to remove the ice maker from the refrigerator model that I have: for some reason this site has deleted my video cite but it is the YouTube video cite that ends in 7HHH03SFdCA Next, because the electrical wiring harness part has changed since production, and the new ice maker part comes with two different harness' (you have to determine which one is most similar to the harness that you remove), take a lot of pictures of the old wiring harness before removing it. There are a lot of different wires that need to be reconnected. There was a prior post by "Greg from Aliso Viejo, CA" that I printed out and followed--that post was also very helpful.

Receive the parts. Review the video. Thought I can do this got down to the screw and I didn’t have is a ratchet small enough to remove the screw so I had to call D.O.C appliances to do the install Michael was here less than 15 minutes

Placed new gaskets on hot patio to smooth them out. Took minion bar off and removed door gaskets. Replaced new gaskets, and minion bar.
Took freezer door off and replaced gasket. I had problems with the first set of door gaskets but customer service replaced them in record time. Service was outstanding. 5 Stars

Easy fix, it's right in the back of the fridge under a cover that just clips in, a piece of foam, and two screws. The hardest part is getting the clips free without breaking them. After replacement it's silent instead of making a grinding noise regularly.

I removed and disassembled the broken frame. I cut a six inch piece of coat hanger and folded in half and crimped together. Then I took pliers and made a hook that I hooked into the metal strip in the back of the refrigerator that holds the upper shelves. After replacing the frame, center rail and glass I bent the wire up under the back of the frame to provide a support. The back of the frame is weak and has no center support.

The old cover was off and I just slid the replacement part that I got from you'll, it just slid in place and snapped close. Perfect fit. Thanks guys

Watched video. Unplugged refrigerator and popped out switch. In plugged connector and pushed switch in place. Plugged in refrigerator and the light worked

I broke the glass in the frig and found partselect and ordered the new glass and had it in 2 days. Very fast shipping.

A jar was dropped on the chef's pantry lid and cracked the lid. I unhinged one side of the lid from the pantry drawer by gently pushing outward on one of the hinge pins. The lid slid out easily. I then reversed the process using the new lid and it went in smoothly. Be sure to align the lid so it rests on the shoulder of the pantry drawer. Simple task, no tools, and less than 5 minutes effort. The replacement part was perfect.

Remove back cover
Remove drip thing from top to tray in the back
Remove fan motor assembly. This is squirrely. Top bends towards you, bottom pushes in to the unit. Not fun.
CAREFULLY remove copper tube that rests on drip tray
Remove tray - there are clips in the front that get released by screwdriver
Clean up
Replace new tray
Replace copper tube
Play with fan motor assembly till it fits. It doesn't look like it's gonna work until it does. See youtube videos on this.
Replace drip thing from top to tray - I forgot this one the first time.
Replace cover.

This is a simple, but squirrely, repair. Right on the border of easy (because so few tools and steps) and A Bit Difficult because of the patience required.