Models > ACR4503SFS1 > Instructions

ACR4503SFS1 Amana Range - Instructions

All Instructions for the ACR4503SFS1
121 - 135 of 237
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Element did not heat
Pulled out element, plugged in new element. About 5 seconds.
Parts Used:
Surface Burner - 8 Inch - 2600W
  • Mary from CHARLESTOWN, IN
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven Elementwas burnt into
Watched the video and did as shown
Parts Used:
Oven Bake Element
  • Fred from APACHE JCT, AZ
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven Wouldn't Heat
Of course, power off first, then I removed the old one and inserted the new one, make sure everything in right place, then turn on power, simple as 1-2-3.
Parts Used:
Surface Burner - 8 Inch - 2600W
  • DAVID from PETALUMA, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
I decided it was the switch that was bad as it would not turn on or anything.
After my husband replace it we noticed that our knob was worn to the point it would not turn on the new switch. I am sure the switch was o.k. so kept the old one and getting a knob to fix the issue.
Parts Used:
Surface Burner Element Switch, Large Burner
  • Christy from OROFINO, ID
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
bunner was not shuting off automaticly
I used the replacement video from the web site. The replacement went great.
Parts Used:
Surface Burner Element Switch, Large Burner
  • Lee from GROVE CITY, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Removing an heating element that burnt into .
Unplugged oven , removed screws ,pulled wires out, removed old element , just hooked wires up , screws .make sure it sits level plugged in. Works great
Parts Used:
Oven Bake Element
  • Jenny from GREENFIELD, IN
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old drip pans made to heating element un ever
Replaced drip pans and now everything is level.
Parts Used:
Drip Bowl - 8 Inch
  • William from DANBURY, CT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
My drip bowls were scorched and discolored and difficult to clean
I removed each surface coil burner from its receptacle; removed the old drip bowls and replaced with the new ones; my stove looks good as new.
Parts Used:
Drip Bowl - 6 Inch Drip Bowl - 8 Inch
  • Claudia from Milwaukee, WI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
door of oven came apart when plastic screw holders broke
put back together with parts ordered. Parts arrived in 2 days!!!! and saved my large dinner party the following day from being ruined. Thank you so much for your parts inventory and for Jenn Air supplying only the part needed and not the entire door. It was a life saver!
Parts Used:
Screw
  • patricia from chipely, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burners needed replacing
Pulled out the old burners and put in the new ones.
Parts Used:
Standard Y-Frame Range Surface Burner
  • Alene from INDIANAPOLIS, IN
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
burned out stove eye, 6"
remove burned out eye, replaced with new eye.new eye does not fit exactally correct onto splash pan as point on end of steel " rod " not pointed enough to slip into mate on splash pan
Parts Used:
Standard Y-Frame Range Surface Burner
  • Robert from Birmingham, AL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Light would not light
Pop old one out and new one in
Parts Used:
SOCKT-LITE
  • Frank from LEBANON, VA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven temperature was 50 degrees off
Unplugged stove.
Pulled stove out.
Unscrewed screws and removed cover.
Removed & replaced sensor.
Reinstalled cover & screws.
Plugged in stove and pushed back in.
Only problem was when I pulled stove out, lid opened and disconnected the gas line to a burner.
Parts Used:
Oven Sensor
  • Gregory from BRIDGEBORO, GA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken Burner
Unwrapped package. That was the hardest part. Inserted into the little spot on top of stove. Tested. Worked great!
Parts Used:
Drip Bowl - 8 Inch Surface Burner - 8 Inch - 2600W
  • FRANCES M. from GRAND JUNCTION., CO
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
2 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Terminal block arc'ed because a wire had become loose.
Ordered and received the terminal block. Installed it along with a new 220V power cord and the appropriate insulator . Ensured the terminals were tight with a nut driver. Reinstalled cover. Then, using the control panel, I did a function check on all the heating elements, clock, oven light, to satisfy all operational requirements. All checked good! And, I was relieved that the control panel had not been shorted out as the terminal block was due to a loose connection. Easy fix.
Parts Used:
Range Terminal Block
  • Larry from Scranton, KS
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the ACR4503SFS1
121 - 135 of 237
Back to Top