All Installation Instructions for Amana Range ACR4503SFB7

Broiler element EXPLODED!

Yes... it exploded. Ordered the part which was delivered promptly. Installed in about 30 minutes with a helper. Just unscrew the 4 interior screws and a bunch of the screws (10 maybe?) on the back panel. Drop the back panel, remove the electrical connections from the broiler element and have your helper pull it out. Shove the new one in carefully through the insulation, attach the two electrical connections and reattach all the screws. Worked fine but smelled a bit as it burned off the new coating. About a 30 minute project.

Parts Used:

Broil Element

Beth from Draper, UT
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

drip pan were burnt out

simply remove the burner take out the drip pan and bowl individually. Install the new one and replace the burner. no tool was used.

Parts Used:

Chrome Drip Bowl - 8 inch

Drip Bowl - 6 Inch

Delroy from Miramar, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

intermittant power to "burner" eye

due to the cooktop age, part was not an exact duplicate. I had to drill new holes in the stainless steel for mounting and ground wire. I used a lot of kitchen matches to heat the shrink tubes over the twist connectors. I should have gotten a heat gun or torch.

Parts Used:

Receptacle Kit

don from Orange, TX
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Element terminal connection loose caused overheating and carbon buildup.

Sanded element contact, replaced connector block. The easiest part of the task was ordering the part online. You made it unbelievably easy. I was amazed!

Parts Used:

Receptacle Kit

Mark from Louisville, KY
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Old receptacle was burnt from lots of use.

Just cut the old receptacle wires and splice in new kit. Very simple and worked perfectly.

Parts Used:

Receptacle Kit

Brenda from Scurry, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

broken burner switch

Easy as pie! Thank you for the illustration to help us pick out the correct part.

Parts Used:

Infinite Switch - 6 Inch

Coral from Duluth, MN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Drip bowls were all rusted.

Removed old rusted drip bowls and put in the new ones. Very easy to do and needed no tools. It made my 25 plus Jenn Air look new again!

Parts Used:

Chrome Drip Bowl - 8 inch

Drip Bowl - 6 Inch

Robin from Seneca, SC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

old drip bowl was worn out

new drip bowl fit perfectly and was a snap to install.

Parts Used:

Chrome Drip Bowl - 8 inch

Richard from Germantown, MD
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

Drip bowls tarnished.

Remove heating element coils. & old drip pans. Install the new drip pans and reinsert the heating elements and insure all elements were level. For aesthetic reasons I replaced all the drip pans - 2 x 8" & 2 x 6".

Parts Used:

Chrome Drip Bowl - 8 inch

Jennifer from Albion, NE
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins

Was this instruction helpful to you?

Thank you for voting!

Not heating properly.

Removed rear panel and removed switch. I placed wires from old switch to the new one. re installed switch an back panel.

Parts Used:

Infinite Switch - 6 Inch

Joseph R. from Candia, NH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Side trim broke

take the 2 screws that hold the handle on out...watch the glass front and the side trims because the handle holds them on. Take the glass out then remove the side trims. Replace the side trims holding the glass in place with 2 pieces of masking tape om each side then install the handle with the 2 screws and remove the masking tape.

Parts Used:

Side Trim - Right Hand Side

Paul from Adamsville, TN
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

oven temperature did not stay as set

changing the part itself was easy, but the sheet metal covering the whole back of the oven was difficult to remove because of some screws that were stripped. The new sensor solved the problem.

Parts Used:

Oven Sensor

Paul from Cornelius, NC
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Gas range would not go into self cleaning mode. When pushing the self clean button, would get three beeps!

The malfunction was narrowed down to the oven door motor lock, located at the upper left back of the unit. Removed two panels from the back of the unit, 8 screws. Then the motor, 2 screws, 4 wire connectors. Reversed the procedure for the installation, and solved the problem. About 30=35 minutes for the job. If your handy at all, it should not be a problem.

Parts Used: