All Installation Instructions for Amana Range ACR4503SFB5

Both right and left side trims were broken.

Ordered both parts using the excellent breakdown illustrations of the door. Received the parts along with video instructions on how to repair.

Parts Used:

Side Trim

Side Trim - Right Hand Side

A D from HOUSTON, TX
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

6 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Element wasn't being controlled by the switch it would stay on high

Ordered a new switch and replaced the old one with it.

Parts Used:

Surface Burner Element Switch, Large Burner

George from FRANKLIN, KY
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

6 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Stove burner wouldn't heat

First I disconnected the power, removed the screw that hold the element in place. Then, I pulled the element out and cut the two wires. I connected the two wires with the new element as the instruction provided by Part Select. I put the element back and screwed it in place. I plugged in the power and turned on the burner. It works. It is really easy to repair.

Parts Used:

Range Receptacle Kit

DAICHI from Louisville, KY
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

6 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

electric coils would not stay flat as drip pans were incorrect fit

replaced drip pans with correct type

Parts Used:

Chrome Drip Bowl - 8 inch

Drip Bowl - 6 Inch

Janet from Philadelphia, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

6 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The burner would not shut off.

Pulled the dial off, unscrew two screws. Pull the switch out from the back. Disconnect the wires from the old switch and connect to the new switch one by one. Set the new switch in place. Sctew the two screws in to hold the switch in place. Push on the dial.

Parts Used:

Infinite Switch - 6 Inch

Richard from CONCORD, NH
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

6 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Store-bought drip bowls wouldn't fit.

My elements just plug in so all I had to do was pull them out and replace the drip bowls. They fit perfectly!

Parts Used:

Chrome Drip Bowl - 8 inch

Drip Bowl - 6 Inch

Sharon from Yacolt, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

5 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

I broke a piece of the trim and had to replace it

took the handle off, replaces the side trim piece and replaced the handle. Very simple!

Parts Used:

Side Trim - Right Hand Side

Gregg from SOUTH BEND, IN
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

4 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven sensor was not regulating heat set for oven

Following your installation, the old part came out easily, with new part installing easily., oven heat is being regulated properly..with range pulled out for part replacement, got that area cleaned too

Parts Used:

Oven Sensor

Linda from SAINT CLOUD, MN
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

4 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

2nd 8 inch burner switch in a little over a year to not always hold selected tempurature.

As a former appliance repairman, the installation went just like the repair instruction video.
Just use care not to scratch anything and clean behind the appliance and cabinet walls, etc. It's worth a hug and a piece of pie!

Parts Used:

Surface Burner Element Switch, Large Burner

LELAND from HERMISTON, OR
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

4 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

bottom piece of range rusty

took old one off and installed new one used electrical tape to hold glass from sliding.Unscrewed moulding and installed new one

Parts Used:

Range Trim Lower (White)

Bruno from LE ROY, NY
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

4 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

temp sensor went oven not heating

the hardest part was moving stove to trplace part

Parts Used:

Oven Sensor

patrick from HUGHESTOWN, PA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

4 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Broiler element not working

It went great. I am not very handy, but with a little help from your website reviews, I was able to easily remove the old broiler element and replace it with the new one in less than an hour. I immediately tested it and found that it worked great.

Parts Used:

Broil Element

Normand from Lincoln, RI
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

6 of 11 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The drip bowls were all caked and corroded.

This wasn't a "repair", but I got an email asking for my story, so here it is. :-)

I followed the owner's manual instructions by pulling out the burner elements, lifting up the old drip bowls, setting in the new ones, replacing the elements.

Parts Used:

Chrome Drip Bowl - 8 inch

Drip Bowl - 6 Inch

Terry from Mountain City, TN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

4 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven stopped heating, error message stated heating element

Very easy. Pulled the stove away from the wall. Used a screw driver to remove the two nuts to release the heat sensor, disconnected the wire, removed the sensor. Inserted the new sensor, plugged back into the circuit. put the two nuts back.
Beware, if the first time you put the oven on, if the error message comes back up (mine did) push the cancel/off button, wait a few minutes, put oven back on. System probably needed to reset. Mine worked perfectly after.

Parts Used:

Oven Sensor