All Installation Instructions for Amana Range ACR4303MFS1

Both burners were faulty, neither would come on or heat up.

Simple, just pull out old burners and slide new ones in place. Tried both, they work excellent!

Parts Used:

Surface Burner - 8 Inch - 2600W

Standard Y-Frame Range Surface Burner

Rex from Keyser, WV
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

large right front burner wasn't going on

turner off circuit breakers for range, i rolled the range out from between counter tops so i could see the burner sw. using a flash light read all the numbers on the switch to my wife who wrote then down, knowing what the switch looked like i could find could find correct instruction video on parts select & check the switch numbers & ordered it. replacing- made myself a drawing of the wiring connections, replacing switch-power off, unscrewed mounting bracket, removed switch, removed ONE WIRE AT A TIME & CONNECTED IT TO SAME TERMINAL ON THE NEW SWITCH, remounted the switch & turner on circuit breakers

Parts Used:

Surface Burner Element Switch, Large Burner

RUSSELL from LEESBURG, FL
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Socket set

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

This burner on our range had no temperature control - it was either full-on or full-off

1. Pull range out from wall
2. Unplug range
3. Remove back cover using drill and screwdriver bit
4. Remove dial handle on affected burner dial
5. Remove two screws to unattach broken infinite switch
6. Disconnect wires from broken infinite switch
7. Reconnect wires to new infinite switch
8. Attach new infinite switch using two screws
9. Use pliers to snap off end of post to fit your burner dial, if necessary. It was on ours.
10. Reconnnect dial handle.
11. Reattach back cover using drill and screwdriver bit.
12. Plug range back in
13. Relocate stove against wall

Parts Used:

Surface Burner Element Switch, Large Burner

Justin from BEND, OR
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

burner would not stay heated had to wiggle the burner to make heat

Replaced with the new burner works like new. Thanks a bunch!

Parts Used:

Surface Burner - 8 Inch - 2600W

Marjorie from Swanton, MD
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Burners weren't heating

Unplugged old burner elements. Popped in new burners. Turned on the burners to test.

Parts Used:

Surface Burner - 8 Inch - 2600W

james from killingworth, CT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The Range took forever to achieve the proper heating temperature with an inability to maintain a steady heat

I removed the bottom drawer,unplugged the Range and pulled it out to expose the rear cover panel. Using a nut driver (a screw driver can be used), I removed the rear panel to expose the Thermal fuse located almost dead center in the back of the Range. Unplug the two wires and loosen the screw holding it in position. Replace the thermal fuse, plug the two wires into the new part and replace the rear cover panel. Return the Range to its original position and plug it in. The job is done in less than 30 minutes.

Parts Used:

Range Safety Thermostat

Robert from Mifflinburg, PA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

oven not keeping correct temp and sometimes would not relight when temp went dropped.t

Slid oven out and took back shield off unplugged sensor took bracket screw out replaced sensor with new one.

Parts Used:

Oven Sensor

Gary from PLUM CITY, WI
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Bottom element stopped working

Unplug the stove from outlet so no power going to appliance. Had to use wd on screws to help loosen
Little bit of effort to loosen. Took new element from package. Replaced screws just tight donot over tighten. Plug stove into outlet turned on. Did a automatic clean. Oven clean and baked cake later I am back in business and 63 years. Was quote 240.00 to from a local repair person. When using wd make sure you wipe any drip from before turning on oven.

Parts Used:

Oven Bake Element

ArLinda from ALTON, IL
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Heating element, broken

Unplugged appliance, removed the 2 screws that mount element. Unhooked the electric wires,with pliers.
Connected, the wires to new element replaced the 2 screws. And was done in about 9 minutes.

Parts Used:

Oven Bake Element

Frank from COLUMBIA, TN
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Drawer guides missingJust

Just follow included instructions.

Parts Used:

Drawer Glide Kit - Black

Mark from Killbuck, OH
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Could not control temperature for 8" burner (front right).

The repair was easy. I unplugged the stove, removed back panel, pulled knob and removed 2 screws to remove switch. Unplugged old switch, plugged in new one and installed the 2 screws for switch. Had to snap off stem for new switch to fit knob (easily done with pliers with provided notch). Put knob and back panel back on. Total time, maybe 20 minutes.

Parts Used:

Surface Burner Element Switch, Large Burner

Sean from LISLE, NY
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

8" surface element stayed on high.

Pulled range out from wall, unplugged AC, unplugged infinite switch, plugged in new switch, broke off end of stem, plugged AC in put range back and tested.

Parts Used: