9864XPB Magic Chef Wall Oven - Instructions

I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

Repair not going well. Can't get the old part out. Have used needle nose plier and still can't get ahold of whats left of the part to pull out. Not for sure what to do next.

My son-in-law installed the new element. First turn off the electricity and remove oven door. Then unscrew all connections to the element.The back electrical wires come out from the top back oven. The bracket screw faces the oven and the electrical wires are so short there is very little room for a screw driver (get the shortest one you can find..abt as big as your thumb if possible).Once that was out the element came out with no problems.Then it's just reversing the step. Again, that back electical bracket is difficult to get to for install. Also, the new screws in our kit were Philips, but the old ones were flat so check those out before turning off the oven light.

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

Removed the two screws on both elements, pulled the wires off, put the wires on the new elements and put the screws back in. Very easy, works perfect.

1. Turned off oven electric power at circuit breaker.. 2. Removed 2 screws at coil at back of oven. 3. Pulled coil away from back of oven. 4.Pulled power wire clip up vertically from coil.One clip was too tight to pull up by hand. Used a pair of pliers. 5 Removed coil and put new coil in place with wireclips. and screws provided.

Loosened the two screws holding the element, pulled the element out of the back of the oven, loosed the two wire leads connected to the back of the element, removed the broken part, placed the new element into the oven, reconnected the wire leads, pushed them back into the insulation in the back of the oven, repositioned the element into its place and replaced the two screws holding it into place with the new screws that came with the new part. Oven element fired right up first try without any further complications. One of the easiest appliance fixes I have ever done!

Very simple. Removed two screws-pulled element out about 3-4 inches-pulled off the contacts-reversed procedure using the provided screws, turned the breaker switch on and everything worked fine. Excellent service from parts select and quick shipping.

put the old one out,put new part in that easy,works like new

Turned off the circuit breaker. Removed the oven door from hinges. unscrewed the old element connection plate. Pulled off two wire leads. Reversed forward steps to completion.

After we got the part in the mail my husband put it on and shortened the wires and put new plugs on the ends of the wires and we had to get a new plug put it on and it was fixed.

Changed bake element in oven.

I unscrewed the old element from the back of the oven. Then I detached the wires and took the old heating element out. I then fit the wires into the new element and screwed it back in using the new screws. It was really easy! I was lucky to have my father in law show me how, since this was my first time to do it.

Removed the oven door, removed old burned element, installed new element. Turned CB back on and tested oven. Reinstalled oven door. Straight forward and easy to follow directions with new element.Local appliance part house said the element was no longer available. Thanks to you I did not need a new oven. Very easy replacement job with normal tools.Thanks

First, we cut the power to the oven and removed the oven racks. I removed the two screws holding the old heating element in (removed easily, I didn't need any WD-40) and pulled the element wiring out of the back of the oven. It took me a while to realize how the wiring was/is connected to the element, but once I did they came off fairly easily with a little coaxing from some pliers. On our model, the wiring thingums fit down onto the element prongs. So, you pull the straight up to remove them. Very technical terms here. After the wires and the new element were connected, I screwed the new element in, turned the power back on and the oven was is excellent working order again.