91195508990 Kenmore Range - Instructions

lift stove top, 2 undermount screws. Then unplug 4 wires, I did them 1 at a time plugging into new burner as I go so I wouldn't screw up. Take 2 screws out of old burner to stove top, # all around circle put screws in same # on new burner.Done Good experience all the way around. Order delivery and install

Remove two screws with nut driver that holds range top down. Turn off breaker or unplug before lifting top. Brace top with 2x4. Take picture with cell phone just in case. Orient replacement part with old burner. Remove one wire at a time and install on new burner in corresponding correcting terminal. be sure they are snug. Drop top install nuts . Test! Done! I am not an electrician!!!!!!!! Please do not publish !!!!

Unplugged the stove from wall, pulled out oven racks. Unscrewed 2 screws that attached the burner to the oven. Pulled the two wires off, be careful not to let them go back into or behind the oven wall, then you would need to take the back center panel off and push them back through. But I bent the wire enough when taking them off to make sure they rested on the inside of the oven wall, got the new burner attached it to the two wires, screwed it back in the oven wall and I was done. Plugged it back in and works beautifully. Whole thing took maybe 15 minutes 30 minutes tops.

Turned off juice
Pulled stove from wall
Unscrewed 2 screws to loosen range top
Lifted n propped top
Unplugged 4 wires
Unscrewed burner assembly
Installed burner-reversed steps to reassemble

I took the oven door off. Laid it down on a blanket on the floor. I pulled up on end going into the door, then went around with fingers to feel where the clip were and grab the clip with my fingers and gently pulled up. Then grabbed the new gasket, found the center clip that goes at top of door and started pushing the clips in. The last was feeding the ends back into the slot in the door.

First, I read what other customers posted on this site about how to change the element. =)

I didn't have a nutdriver so I used a pair of pliers instead. They worked fine.

Pulled the stove away from the wall, unplugged it, removed the 4 small nuts holding the small plate over the back of the element connections, slid the connectors off the element prongs, removed baking racks from oven, removed 3 screws holding the element in place, slid element out.

To put the element in I simply did the same thing except in reverse order. The entire process was so easy and only took minutes to complete! However, like another poster, I took the opportunity to clean my oven before putting in the new element.

The best part of dealing with partselect....the element only cost me $51 vs GE site price of $91, Plus the element arrived the morning after I had placed the order! Thank you partselect! In gratitude, I posted my happy experience and a link to this site on my facebook! Thanks for everything!

Easy

turn off power to the stove
Pull the stove away from the wall
remove center (metal) wire cover (5/16 nut driver needed)
disconnect 2 quick connect clips
back to the front of stove, open oven door
using 5/16 nut driver, remove 2 screws
pull out old element
insert new element
using 5/16 nut driver, reinstall 2 screws
go back to the rear of stove
reconnect 2 quick connect clips
reinstall center (metal) wire cover (5/16 nut driver needed)
turn power back on
ready to cook

The repair went very well. The second repair comnt to remove the hinge screws was a good correction from the first description. I had to go to that parts diagram to realize that the the two metal sleaves were insulation spacers for the two top screws.

My baking element burned out after being exposed to grease and other remnants of past feasts. After some research the repair seemed straight forward so I figured I'd give it a shot. Overall it's fairly simple, though there are some things to watch out for.

I didn't remove my oven's door, which restricted my movement somewhat. After removing the bolts I was able to easily remove the old heating element and expose the two connecting wires. One wire had much more slack than the other. I connected the wire with more slack first. However, I'm somewhat uncoordinated and doing so caused the other wire to retract within the unit. I had to pull out my stove and remove the back panel, which was easy. The retracted wire was easy to find, but there was no slack available through the back access either. I actually had to unscrew the wire from the thing that is connected to the wire that plugs in to the outlet first. Doing so gave me enough slack to connect the heating element to the second wire. After that I just reconnected the wire to the outlet connection and put the back panel back on!

About 45 minutes in total time. Most of which was figuring out the approach to getting enough slack to connect the second wire and working around the oven door which restricted my movement.

Got door off no problem used screw drive to release locks and lifted door off. Took 3 1//4 screws out the 2 3" long screws out to separate door half's took screws of hinges and then8 1/4 inch screws of sheet metal that covered window. Replaced window and reverse what I did taking apart. Still having trouble getting 1 hinge to connect to stove. Help would be appreciated.

The element ignited and burnt like a sparkler. I unscrewed the bolt/screws holding it in, and pulled like I had on older models. The clips holding it didn't come undone, but the wires hit the side causing a huge flash. It was still hot, even though it wasn't turned on. You need to unplug the oven, or turn off the breaker. I unplugged and took the back panel running down the middle off (4 screws), and undid the clips. Putting the new one back in was easy. Insert the element ends through their places inside the oven. Screw them in place. Hook the wire clips on in back, and replace the back panel. Installation took less than 5 minutes.

burner went out Thursday evening, ordered new burner at 8:30 pm, new burner was delivered Saturday afternoon, removed back panel from range, removed burner, replaced burner, re-installed back panel. Took less than 1/2 hour to replace. Hardest part was finding the correct size socket.(ALL WITHOUT HELP FROM HUSBAND.) Thanks so much for prompt delivery.

Using a set of nut drivers, I unscrewed the element from the back of the stove, I unscrewed the thermometer, and unscrewed the brackets holding the element to the top of the oven compartment.

After the element was free, I pulled it out of the back of the oven, exposing the wiring. Using pliers, I disconnected the two wires, retrieved the new element, and re-connected the wires to the new element.

I reconnected the thermometer, pushed the element back into the oven, reattached it to the back of the oven and the brackets to the top of the oven compartment.

first pull the range out and disconnect power cord
remove back cover (5 screws)
Open oven door and remove racks
remove (2 screws) that secure bake element
pull off 2 wires
put new element in replace 2 screws
from the back of range plug the 2 wires to element
replace back cover
really easy