9119238210 Kenmore Range - Overview
Sections of the 9119238210
[Viewing 5 of 5]
Keep searches simple, eg. "belt" or "pump".
Drip Bowl - 8 Inch
PartSelect #: PS244696
Manufacturer #: WB32X106
This 8-inch chrome drip pan is designed to sit beneath the heating element on electric ranges, serving as a protective barrier that catches spills, drips, and food particles during cooking. Measuring ...
$70.92
Special Order
Drip Bowl - 6 Inch
PartSelect #: PS244697
Manufacturer #: WB32X107
This six inch chrome drip bowl is intended for use with rolled terminal style plug in surface element units.
$19.95
Special Order
Single Heating Element Support Clip
PartSelect #: PS243701
Manufacturer #: WB2X9719
This metallic clip is used to help support the broil element. Sold individually.
$21.50
Special Order
Range Infinite Heat Switch Kit
PartSelect #: PS16216966
Manufacturer #: WB21X36771
The infinite switch controls the stove top surface burner. This switch will work with most of the electrical range models with coil burner elements.
No Longer Available
Surface Burner Terminal Block Kit
PartSelect #: PS232606
Manufacturer #: WB17X210
This kit comes with the terminal block, mounting clip and wires.
$91.36
Special Order
Bake Element
PartSelect #: PS359687
Manufacturer #: 4328405
This closed hinged style bake element is found on the bottom of the oven and is used for baking food.
No Longer Available
Common Symptoms of the 9119238210
[Viewing 1 of 1]
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
There was no heat on the coils.
I opened the lid, and found that the terminal blocks were burnt, the wires were melted. I ordered one set of terminal block to replace the burnt one, and it worked. Before I started, I shut off the electricity in the whole house to be safe.
Parts Used:
-
Shaohui from East Lansing, MI
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers
48 of 52 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Large burner would operate on high setting only.
1. Removed the back panel.
2. Disconnected the wires from the old switch while connecting wires to the new switch one at a time.
3. Installed the new switch and broke off the excess metal on the post which fits into the burner knob on front of the range.
4. Replaced the burner knob and replaced the back panel.
2. Disconnected the wires from the old switch while connecting wires to the new switch one at a time.
3. Installed the new switch and broke off the excess metal on the post which fits into the burner knob on front of the range.
4. Replaced the burner knob and replaced the back panel.
Parts Used:
-
Ernest from Bellevue, NE
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Socket set
22 of 28 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Surface burner coil did not work.
TURN OFF ALL POWER TO KITCHEN. Took off all burner coils and plates below them. Lift hood. Locate part. Remove old part and replace with new part in same way as was previously installed. The wire that comes with the kit is actually too much wire, but just arrange it the best you can and leave it....no big deal. I didn't have a magnet, but needed one. The wire from burner coil to switch runs through a harness which is screwed on to the body of the oven (below the range). Be careful NOT to drop it behind oven when taking it out. I dropped it and took forever to get it. That turned a 20 minuate job into an hour and a half. Otherwise this is an easy job that anyone can do. Refrigerator compressor is next. Have fun.
Parts Used:
-
Gregory from Mont Belvieu, TX
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers, Socket set
23 of 33 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!