91136655591 Kenmore Range - Instructions

replaced lights in refrigirator and freezer

Very easy once I got the right parts - when I ordered I didn't realize that the center holes were what determined whether I needed "small" or "medium/large"...I was going by the exterior dimensions I returned 3 of the 4 I ordered and re-ordered the right size. My wife ended up replacing the rest of them herself after watching me do the one that did fit. Looks like a new stove!

I replaced the igniter under the knob.

Shut of electric supply. Remove knobs and open top cover of cook top by removing two screws near each burner and replace switch.

With multimeter checked resistance of oven sensor. Specs called for 1100 ohms. It was off by 27 ohms. The sensor from Part Select had exact wire connection as original. Then just matter of undoing old and reconnecting with new one.

One unsatisfactory event. I asked Part Select why my clock did not work or light up(timer works ok) . Answer was: sorry we have no time to help you. That soured the otherwise happy experience.

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

The top is all glass so I took my time. There was about 12 screws and double sided tape. A lock washer holding the igniter on. It also gave me a chance to clean the hard to get to places. Your price was almost half of what a suppier here and getting it would have been 2 weeks compared to your 48 hours to my door. Thanks again

I basically had to disassemble the top part of the stove to get the clock out. Once I got the clock out, replacing the plate was trivial. It attaches with a sticky/tacky back. Reassembling the stove took another 30 mins, but went relatively smoothly. The final job looks great and the stove seems to function as usual.

By myself

Easy

Followed the instructions

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. . . ) It was like drinking juice

Cut off power to the cook top and confirm that power is actually off. In my case, this involved turning off a cicuit breaker. Remove all burner control knobs by pulling straight up. Lift off all grates, burner caps and burner heads. Remove two phillips head screws from each burner bowl. Pry each burner bowl up and unhook the ignitor wire. I labeled the wires to make sure I got them hooked back up right. Remove the four burner bowls by lifting them off. Make sure you remember where each goes so you can reinstall them in the right places. Pry up the glass cooktop and lift it off. I took the cooktop ouside and gave it a good cleaning. This plus cleaning around the cooktop and cleaning the burner bowls is what took most the time. Lift the defective switch off and disconnect the two wires. Align the flat in the new switch to the off position. Reconnect the wires and install the new switch on the valve stem. Reinstall the cook top. Reinstall the burner bowls making sure to reconnect the ignitor wires. Reinstall the burner heads, burner caps, grates and knobs. Turn the power back on and make sure everything works correctly.

Repair was easy once I got the correct part. When the parts were listed as small and medium large I thought they were talking the diameter of the bowl. It turns out they are talking about the center hole in the bowl. So I needed one small and three large. Everything great now.....stove looks great and clean.

When I got the part I removed the tin cover (two screws)on the back of the range. I removed the sensor by removing the two screws inside the oven and pulled out the sensor. taking the instructions advise, I checked the sensor with my ohm meter and although it read 1.1 ohms as compared with the recommended 1.09 ohms at room temperature in the instructions, went ahead and changed the unit. The connector did not fit my particular model so I spliced the wiring and using the two included wire nuts made the connection. I reinstalled the sensor, reattached the gas line, plugged it in and tried the oven before I put it back in place. The oven works great now and it was super easy.