9113651190 Kenmore Range - Instructions

First I disconnected power, then removed two screws from igniter & cliped two wires. Then installed new igniter & with the wire nuts supplied refastened to supply lines in oven.
PartSelect makes repairs quick & easy. It just takes a little smarts on your part.

Lifted door off the front of stove, real easy, but heavy, took out old hinge, and replaced with new hinge, I just looked where everything was before, I replaced with new, replaced door back on, and I was finished.

Pulled out bottom drawer and showed my 13 yr
old boy that the spring needed to go back in same hole, then he did the rest. It was so easy, even a 13 yr old can do it.

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

Remove the front door-lifted off(no tools) removed the floor of the oven (2 standard nuts at the rear). nut driver to remove the igniter. Took longest to untwist and retwist wires & dropped screws. reassembled and tested...worked perfice. this is the 4th time I've used Parts Select and It's great....Thanks and keep up the good work!

Removed the bottom plate inside the stove by removing two back screws. The burner was exposed. roved a total of three screws on gas burner to remove the entire assembly. Removed two screws from the old igniter and then put new one on. Save the old connectors because they have unique connectors. Cut old wire and strip 3/8 inch of wire cover off. Using the supplied wire nuts. Caution use only supplied wire nuts because they are meant for heat. connect old wire to new wire of the new igniter. Reverse order of screws that you did for the job. That is it

Remove the broiler pan to get at the 2 nuts that hold the gas burner, remove them and then you can get at the 2 nuts on the back side of the igniter.

I was able to access the burner and igniter by removing the broiler drawer. The flame guard was removed with a nut driver and the old igniter with a phillips screwdriver.

The electrical wires had to be spliced into the old igniter wires as they did not come with the factory connectors. However sire nuts were supplied.

After replacement of the igniter with the new one .. it would glow and about a minute later the gas would come on. However the gas from the burner did not light. I had to adjust the bracket closer to the burner to correct the issue.

Note: The igniter is wired in series with the gas valve. This means that it will continue to glow even after the burner lights durning oven operation.

I figured out the problem, ordered the part, and replaced it. Four hex head screws, two wire nuts, and two thum screws latter it was working.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...And then I installed
ignitor tightening the two screws and connected the two ignitor wires with the provided wire-nuts.
Mike Polcho

It was a simple repair removed the oven door, and the oven bottom plate. removed the screw that held the burner tube to gain access to the two screws that hold the igniter in place clipped the wires. put the new one on with butt end wire connectors instead of the wire nuts supplied. screwed the igniter back onto the burner tube put the burner tube back in place and secured it with the screw, replace oven bottom and door the whole repair took 20 minutes.

IThe schematics on the website were helpful for how everything goes together. I just followed the picture and then unscrewed all the screws that held the ignitor to the gas pipe. Have to pull out the gas pipe out first so you can get to the bolts, easy to do when you pull out the drawer and unscrew the hold down for the gas pipe.

No directions came with the part, and the length of the new wires weren't long enough nor did they have the attachment pieces that are needed to plug in the wires. However, helpful tips from others on the website told me that you have to cut the wires off the old part and screw the wires from the old to the new with the white plastic wire couplings. Worked like a charm!

It was a simple procedure, and I saved myself buying a new stove or paying someone else to fix it!

i followed the same directions others had posted - good tip to remove the oven door for easier access - i was nervous about stripping the wires to splice together, so i made my hubby strip the wires for me :) - did all the rest myself. no trouble at all - if a girl can do it, anyone can do it!

My husband removed the two screws t hat hold the element in place, Then he pulled the element out about 3 inches and disconnected the two wires and replace the element with the new igniter put everything back and now its working like a charm