9113618811 Kenmore Range - Instructions

The spark control module is located in the top section near the clock. Take off the back cover. Use needle nose pliers to disconnect the wires. The modules are marked with letters so connecting the new module is very easy. The range works great. My Kenmore is a 1985 model.

Really easy.
1) Pulled up on oven door and removed it.
2) Removed lower drawer to access springs.
3) Pay attention to which hole the springs are attached under the oven.
4) Remove spring with Needle Nose Plier. If you remove by hand, the spring will likely cut your finger....like mine.
5) Unscrew 3 screws of old hinge assembly.
6) Reverse process when placing new assembly in place.

I tapped the screwdriver with a hammer lightly on each of three screws to loosen them. I checked to see the position of the spring on the hinge. I then removed the hinge, put on the new hinge and placed the spring in the exact same position. The door works very good. The hinge replacement was a no-brainer.

Replaced old ignition module with new module from parts select.
The most important tip was to label each lead before removing from old ignition module.

Easy

After reading the other DIY's directions, we explored how to remove oven door. When the part came in, my sister who was visiting, removed the oven door (30seconds), removed bottom drawer (30 seconds), noted where spring was attached, took off screws and spring, installed new hinge with roller, took a minute to decide if the new hinge came through the back or the front (front), she reattached the spring and screws. Put door back on and then struggles to put the drawer back into place. Total time less than 5 mintues, most time spent on returning bottom drawer to its home. Thanks part select for helping me not burn my self every time I try and get food out of the oven!!! I open the oven door all the way and am so delighted!!

Easy Repair. Remove the storage draw under the oven. It lifts out. Lift oven door off of hinges. Remove 3 screws & unhook the spring. Reverse the procedure with the new hinge. Good as new.

The part arrived on timed and fit perfect. The repaired took 1/2 hour and everything works perfect. My wife thinks I am the best

I removed the door by pulling it up (according to the instructions). Than took a philips screwdriver and
removed the three screws in each hinge, unhooked the springs
and slid the old hinges out of the slots.
The new hinges slid into the slots perfectly so the screws
were installed, the springs rehooked and the door installed.
Real simple.

After reading other stories, I knew enough to slide the lower drawer out and take off the spring. 30 second job. I did not realize that range doors slide vertically off the hinge, did that in about 2 mins. Put the new hinge on in 2 mins (3 Screws). Slid the door back on and done. Works like a champ. My wife has her eye on new stainless appliances. Sadly, she'll have to wait a while longer.

Removed the oven door. Released spring on hinge. Removed 3 screws. Removed broken hinge and replaced new hinge reversing these steps.

First I removed the oven door from the support hinges. Next I pulled the bottom pan drawer out to get to the tension spring. I released the tension from the hinge, unscrewed three screws that held the hinge in place. From there I replaced the hinge put all components back in place and did it all under 20 mins. The part was received with in 3 days from PartSelect so I was very satisisfied with the service and ease of repair.

Pulled the three screws off unhooked the spring then removed the hinge. attached the the new hinge to the spring put the screws back in slid door back on took less than 15 minutes.

Slid door off hinges. Removed 3 screws which hold hinge in place. Removed drawer to access spring for hinge. Gasped at all the crumbs and crap which had collected underneath the drawer. Cleaned up crumbs+crap from floor. Disconnected spring from hinge and removed old hinge completely. Installed new hinge with 3 screws. Attached spring to hinge - center hole fitting. Slid drawer back in place. Angled hinges outward in order to re-install door. Slid door back onto hinges. Door now operates nice and smoothly. Job well done.

Pulled oven door up and off. Removed old hinge and installed new hinge. Replaced oven door. It was a very simple job. The whole project took less than 15 minutes.