All Installation Instructions for Jenn-Air Cooktop 88890

8 inch element not heating in cooktop

I removed the old element. I then plugged the new element in place. Simple repair, no tools required. Turned the cooktop element on to test for proper functioning. It heated properly. Repair completed.
Ordering the part was easy and it arrived within 2 days. Very happy with Parts Select service.

Parts Used:

Delta Frame Surface Unit - 8 Inch

LouAnn from Maquoketa, IA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Burned out burner

Pulled out the old burner and plugged in the new!

Parts Used:

Drip Bowl - Chrome - 8 Inch

Drip Bowl - 6 Inch

Esther from Alexandria, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

My electric range burner was not heating.

All I had to do was remove the old burner and push the new burner into place. It couldn't have been easier.

Parts Used:

Delta Frame Surface Unit - 8 Inch

Joyce from Oceanside, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Drip pans were a mess

Replaced the drip pans

Parts Used:

Drip Bowl - Chrome - 8 Inch

Drip Bowl - 6 Inch

Chhristopher from Houston, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

lost one of the knobs

Ordering and installing was easy. The hardest part was getting the exact match to 20 yr. old appliance knobs. First one I ordered had wrong shaft hole, but it matched perfectly in design. Decided to reorder and just replace all four with matching new-style knobs and the correct shaft hole. Yeah. Looks great and REALLY easy to install.

Parts Used:

Surface Burner Knob

Sabra from Dallas, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Ring adapter was the original and was pretty well worn through.

Removed the old adapter and replaced it with the bright and shiny new one that fit perfectly.

Parts Used:

Chrome Trim Ring - 8 Inch

Edward from Brooksville, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

The original grease filter was damaged in our dishwasher (it is quite fragile) and needed to be replaced.

1. Remove the exhaust vent cover, located in the center of the top of the range. It just lifts off.
2. Swivel the clamp 90 degrees to release the filter.
3. Remove the filter and throw it away
4. Place new filter in place and lock in place by rotating the swivel clamp back 90 degress.
5. Replace the exhaust vent cover

Parts Used:

Range Grease Filter

Martyn from Middletown, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Broken knob dhaft

Replaced wires from broken to new part.

Parts Used:

Surface Unit Infinite Switch Kit

Richard from THE WOODLANDS, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

blower motor was making loud noise

removed motor, saw that stablizers were broke and went to a local parts supply shop called SUNDBERG and was given a price of about 49.00 for three stablizers. at that point i went to the internet and found PARTSELECT.COM were i found the same parts for a fraction of the price,17.00, i could not believe it! SUNDBERG customer service was horrible.PARTSELECT custormer service is great and was just over the internet,any how the repair is done no more loud noise and wife is happy again ,for awhile.thanks keep up the good work.i tell everybody about you guys.

Parts Used:

Range Motor Isolator

alphonso from plainfield, IL
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers, Socket set, Wrench set

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

burner receptacle was broken

The repairs were very simple we just disconnected one screw then removed the old one and replace with new one. The left side took a little longer, because of the 8 screws we needed to remove to take the back panel off. But once we had it taken off the replacement was a snap. Nothing to it.

Parts Used:

Drip Bowl - Chrome - 8 Inch

Drip Bowl - 6 Inch

Surface Burner Receptacle Kit

Molly Grace from Victoria, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Elec. stove-top knobs (imprinted with HI to LO numbers 1 to 10)worn to non-readable.

Knobs sent fit the shafts, but due to molded internal stop wouldn't seat. Had to drill out the stop, and also file down the shafts a bit for knobs to seat acceptably closer to stove-top.

Parts Used:

Surface Burner Knob