8539A Norge Dryer - Instructions

unplug dryer, lift top, remove 2 screws holding front, lift & swing front to right, use nutdriver to remove two screws holding igniter and other piece attached with same screws, a couple wiggles and out, unplugged igniter, plug in new, reposition new igniter and other piece, replace screws, repositioned front panel, replaced front panel screws, dropped top back in place, plugged in and wha-la. Heat.
Original Igniter had a hairline crack in it causing it to intermittantly fire. Thanks PartSelect, right part and speedy delivery.

Easy Job.
First take a flat head screw driver and pop the top placing the screwdriver in between the front panel. The top of the dryer should pop up.
Then just pull it up and over towards the back.

Then unscrew the front panel and move it out of the way leaveing the front door atached to the panel.
Once you open the front panel' You can pull the dryer tub out by sliding it out and at the same time you need to push the belt towards the back of the tub until it comes off.
Now you can get to the ingiter by first disamablethe gas
housing first.
Simply by taking one screw off and disconnecting the gas line fitting in front of the dryer. Also disconnect the 3 sets of wires that are connected to that piece and the igniter.
The hole piece will then come out with the igniter attached to it.
Next disconnect the igniter from the piece and replace it with new one.
Then put back togather the same way you took it apart.
Reinstalling the tub.
When it's time to put the tub back in; there's a trick to that.
Put tub in about 3/4 of the way in, put the belt around the tub and let the rest hang to the floor inside dryer.then crawl into the tub and stetch your head and arm through the tub on the back side.
Then you can get to the belt and route it into the motor and the pully that is spring loaded it makes it so much easer that way then trying to run the belt and route it in place from the top. Once that is done now you can adjust belt back to its orignal position then push the tub back in place. Reinstall fron panel and your their.
Total cost 36.00 plus shipping. Thats a lot cheaper then a sevice call and labor

Remove back panel n u can see the sensor and easy to replace thanks to the print out i was provided love this website

I had an issue where I was not getting any power to my ignitor. After replacing the ignitor with a fresh one, the problem persisted. Next, I went hunting all the fuses and therrmostats for continuity. All seemed fine. So finally I decided to jump the flame sensor which is located on the outside of the flame tube. WHALLA! It ignited the glow plug. So with one 1/4"" nut driver I removed the single bolt from the unit, then I used a pliers to remove the two wires from the old unit. I replaced the sensor with Tue new unit and all was well. It took less than 5 min once I diagnosed the problem.

I inserted the clip

First I removed the screws that held the part in place, but this proved to be the hardest part for me. I had to find the right kind of screw driver . It was not a slotted or Phillips. It was more star shaped. Once I had the right tool, the rest was pretty easy.
I then opened the top of the dryer to be able to lay the front on the floor. There were wires connected to the front, however, so I had to remove the part that the wires were connected to by slipping it out of the bracket that held it in place. Once the front panel was on the floor, I simply lifted the old part out and placed the new part in. I closed the front, replacing the part with wires back into the bracket, locked the top down tight, replaced the screws, and I was finished.

Sensor is in the front lower left. Gas off, electicity off. Removed two screws for the filter, pry/lifted the top up and taped it too the overhead cabinet, removed two screws inside top of front panel, lifted pandel with door closed staight off. Two screws to remove the flame sensor braket. unplug the old sensor install the new one and reverse everything. With others suggestions I purchased temperature switches etc. but the radiant flame sensor was the problem. I now have some spare switches for future. Excellent company and very quick service. Oh, Sears wanted 200.00 just for the service call, I live rural.

1st thing,,,,unplug dryer from electric,,,Raised the top of dryer, took 2 screws out that held front of dryer on, removed 3 wires and dropped front of dryer. exposed blower wheel,, removed all nuts holding front of blower wheel, removed clamp on front of wheel with pliers, removed old wheel, replaced everything in reverse.

After reading the comments of on-line customers, I realized the dryer opens like the hood of a car and then you pull the front of the dryer door off in order to get to the two screws holding the old lint duct housing unit. Putting the new part on was easier, but I would have appreciated a detailed picture along with the written instructions. Thank you for your quick delivery. Kathleen Yosso

loosened two screws on back of top,lifted top away from front panel.it just lifts off front corners,removed two screws at top corners.lift front panel up and out,this panel supports dryer tub,remove slowly,unplug door switch parts are located left side bottom two screws holding in had to have wife hold drum up to put front panel on

Ohmed coils and both had continuity so I changed radiant heat sensor. No bench test for Radiant Heat sensor. Same problem. Changed both coils and dryer works fine. Weak coils were my problem. I read thru the same issues in Parts Select forum and it said Radiant Heat sensor was problem 25% of the time. With coils having continuity and no ohm value specified for coils I made wrong choice but, I have spare parts and look for another 10 years of life in the dryer. Nice to have this forum to research appliance repair. Very helpful for parts location and installation. Dishwasher is next!

It took me a bit to figure out how to get the outer case to come apart (there are two spring-loaded latches under the front edge of the lid, had to insert a putty knife at just the right spot then lift up the lid). Once it was taken apart, I manually spun the drum to see where the noise was coming from and it was obviously coming from one of the two wheels that support the rear of the drum. Took out the drum after sliding the belt off and replacing the wheels was a piece of cake. They are held on by E-clip style retaining rings, which I destroyed when removing them with a pair of pliers. Luckily the new set comes with new retaining rings, along with the required washers and spacers. I also replaced the metal pins that the wheels spin on, since mine were showing wear and I wanted to make sure it wasn't going to keep squealing after I was done! All in all it was pretty easy! Before you take the belt off, make sure you take note of how the belt winds around the tension wheel so that you put it back on correctly! My girlfriend was VERY impressed that I was able to fix her dryer for about 1/10 of what it would have cost to get a new one!

It was supper easy. I was able to order the correct part from the detailed description you provided. I just opened it and slid it into the slot for a perfect fit.

I wish I had done it sooner. My filter had holes in it for some time.

I followed the advice posted by other customers. I took the front off the dryer, put the door back in place and ran a cycle. I could see that the igniter was heating properly, but no gas was flowing. Based on what I read I concluded that it was a problem with one of the gas valve coils. It was relatively inexpensive to replace both (and the dry is 10 years old), so I didn't go to the trouble of determining the bad one. I replaced them both. Obviously I unplugged the dryer (no need to turn off gas). There were 2 screws that held the bracket in place which holds the coils. I disconnected the coils, removed the bracket screws, replaced the coils, reattached the bracket screws and reconnected the coils. I then reattached the front plate to the dryer. It was very easy and took about 20 minutes and I had never worked on a dryer before.

Actually, I was the handy man. First I removed the front panel. Then I used 3 - 2x4s to hold up the drum. Then I slipped the belt around the center of the drum ,motor,and around the pulley at the bottom of the dryer. That was it, and then I put it back together. My wife was amazed and proud that I did it without calling for help! No Problem!