7MMVWB850WL0 Maytag Washer - Instructions

old pump had plasitc fatigue allowing water to leak from drain pump. Noticed new oem pump was reinforced in that spot, so must be common problem. new pump came with heat shield that old pump did not have, not a problem though. Placed washer on front side down on floor. removed old pump, installed new pump

The washer would enter the spin cycle, but after starting to spin, would quit, and beep repeatedly. The fault code shown was DL. The manual cited DL as Door Lock malfunction. A check of the door lock switch suggested an internal problem. Sears offered the part at a far greater price, and shipping was several times more than PartSelect.com. PartSelect was chosen, and the part ordered on-line. Within two days the part arrived. Installation was simply a matter of lifting the top of the unit on which the door is supported. IT is done by inserting a narrow screwdriver into the separation, and pressing on the two metal springs holding the top in place. The old part was simple to remove by extracting two phillips head screws and removing the cable from the cable mounts underneath the top surface then threading the cable and plug back through the cable hole. Before that could be completed, the rear cover of the control panel was also removed, and after the plug of the defective switch was removed, the new cable was connected, and threaded back through in the reverse of the removal of the old switch, the phillips head screws, the control panel rear cover and returning the unit top to the resting position and snappin it into place. The Power ON check indicated that the problem fault code was cleared. The unit functions normally with the new switch. Hats off to PartSelect. The part was available in stock, and shipped promptly, and at substantially less cost than Sears.

Just pulled the old water pump off and replaced with new one and was good to go. Thank you so much for sharing the problems and how to fix. Dean

Removed the softener dispenser and cap that's under it. Used 7/17" socket with an 18" long extension to reach the bolt that holds agitator down. Pulled auger off, pulled lower agitator off. Removed the 6 philips head screws that hold basket hub in place. Removed hub and installed new one, replaced screws. Lightly greased spline and reinstalled lower agitator. The auger has the cam section in it. A trick to get the rollers in place is to secure them to the cam with rubber band. Have string tied to the band. Insert the cam and when almose all the way in, pull rubber band off and the rollers stay in place. Reinstalled the bolt, cap and softener dispenser.

Removed broken hinge, replaced with new.

need to get washer turned on side where you can work underneath the machine. This job is alot easy if you get where you can see good and have plenty of room to work. You have to unhoook the wire from the old pump and then take the two mounting screws off from there you unhook each hose by squeezing clamp together and sliding backwards away from pump. A pair of needle nose pliers can make this process easier if the clamps are turned in an hard to get to position. You mount the new pump the same way as taking off the damaged pump. Take a screwdriver to help you slide the clamps up onto the new pump makeing sure the sleeves are completely over the new pump fittings and the clamps are slid up evenly, so you want have any leaks. Then replaces wiring harness and mounting screws.

Easy repair. Went to You Tube and saw PartSelect video. The best instructions...should make a link from parts page to video of install. Also replaced Heat element on Dryer. Watched video first.

I removed the screws from old hinge that had broke. The piece came right out with ease. I slid the new hinge in to the hole that it went in. No struggles with ease. Lined up the screw holes and put the screws back in. Finished! Works like a charm.

I removed the screws holding the broken hinges and put the new hinges on. It only took a few minutes.

First off always remember to empty all pockets, coins etc ruin pumps.shut off water supply, unhooked water lines and drain into pan.tilted machine forward so i could work on pump which is located lower left. drain pan under pump area, removed 2 rubber water hose's 3 5/16 screws with nut driver. Very carefully un clip rear of housing and removed wire harness. installed new pump

Went to youtube.com and watched the video that took you step by step in replacing the lid lock assembly.

PLASTIC motor housing gets hot and become loose. causing bearing to spin and make noise . Replaced motor that was quick and simple by removing 3 screws and 2 hose clamps , pluged up motor and begain washing again with no problem . Just wish motor housing was not plastic .

Unplug washer. Use scraper to depress spring steel catches under top cover of cabinet. Raise and support cover. Remove lock mechanism from cover using nut driver and remove switch and cable from spring tension clips. The last cable stay is zip tie/plug; pry it from hole in cover. Don't worry about saving this cable stay as the new switch has one pre installed. Before lowering cover place an object such as a rolled up towel over the cabinet spring catches to prevent engagement. Then lower cover. Locate two screw on back of control panel and remove with nut driver. Just below control panel on back side of cabinet is a single screw securing a small cover plate. Remove screw and plate. Lift control panel and turn it over. Locate plug for the latch switch and disconnect it. Then set control panel back in place. Raise and support top of washer again and pull faulty switch and cable assembly from washer. Attach new switch assembly to top cover and place cable into spring clip and insert plastic cable stay into hole. Route the connector through the opening the faulty one was pulled from. You may now close the top of the washer. Lift and turn over control panel connect new switch plug and set control panel back in place. Replace screws on back of panel and the small cover and screw. Plug washer power cord in and you should be done.

It was not easy but I dit my sell

reemplace the lid lock assembly