79578402804 Kenmore Freezer - Instructions

My son just pried out the old switch with a screw driver snapped out the old one and snapped in the new one. Pretty sure even I could have done this. Very quick and easy. Thanks. :-)

Cover the putty knife with tape so you do not scratch the side wall where the switch is located. Slide the knife under the edge of the switch and push in a bit towards the switch and slightly twist to pop the switch out of its hole. Disconnect the wires from the switch and simply plug in the new switch. Push wiring back into the hole and careful push the switch into the hole until it snaps into place.

IMPORTANT: REPAIR EASIER WITH ASSISTANT! Pull frig from kitchen cabinets & unplug. Remove food from freezer & frig doors. Have assistant hold freezer door closed against freezer. Remove hinge cap from top of freezer along with hardware using socket wrench. Carefully lift freezer door from hardware that joins the bottom of the freezer door to the top of the frig door. Rest freezer door upright off to the side. Have assistant open frig door & SUPPORT BOTTOM. Remove hardware from top of frig using crescent wrench & screwdriver. Carefully lift frig door off joint & lay on side to gain access to hardware on bottom. Remove hardware using a screwdriver & replace worn nylon bushing. Reverse disassembly steps. Remove frig & freezer door shelves & clean inside. Clean outside frig, especially the back vents. Clean the floor where frig lives & push back into place. Enjoy clean SELF-CLOSING, NON-GRINDING frig door!

Unplugged the fridge. Used a screwdriver to loosen the switch. Easy to disconnect from fridge and just plugged the new switch in. Popped right back into the side of the fridge and worked perfectly.

I was told the mother board went out. Took a few months to finally get one myself after repairman didn't come through. It turned out not to be the motherboard that sears repairman tested it for and said that's what it needed. I found Parts select after going round and round with sears parts refusing to accept return. There prices were better, as well as shipping and it came so quick i thought it was over night. The controller assembly was not the problem so we have it for a spare now. It was the freezer fan but even after installing it nothing would work is why we ordered the controller assembly. after 2 days and about 7 hours of checking, taking apart, rechecking assembling by my determined electrician it turned out to be a loose wire. LOL hope this helps someone. I'm just glad to have my fridge again! Blessings!!!

slid screw driver under edge of switch, easy.

purchased a new switch. The old switch just needed to be lightly pried out with a screw driver, then it was simple to unplug the old, and plug in the new. Voila! Light !

When the shelf was delivered, all we had to do was open the door of the fridg. and put the glass into place. pretty easy, huh?

I popped the old switch out of place and then disconnected the wire harness from the switch with a pair of needle nose pliers. I then inserted the harness into the new switch and popped the switch into place. Super easy and fast.

Uncoupled the old connector, replaced with new connector and attached supply line. Repair easy with right part, prior to ordering the right part I had tried a compression fitting and it still leaked. U-tube and others demonstrating repair assured me I was on the right path.

I called LG and followed the instructions given over the phone. The instructions couldn't have been simpler. Disconnect the appliance for several hours and then connect again. I disconnected the appliance overnight, cleaned out the freezer, and reconnected it. Problem solved. Did not need to call a repairman and did not use the clips.

This was late on a Sunday afternoon. I immediately called the store where I purchased the refrigerator who told me to go on-line for any parts. So I went to PartSelect and was able to find the correct part very easily and then order it. It arrived on Thursday without having paid for any upgrade in shipping time.I am very impressed with this company.

I removed the broken rail & installed the new rail with a screw driver. The screws were located in somewhat difficult position. The rail works OK but has a tendency to stick & the tray holder sometimes slips out of the new rail.

Caution removing plastic molding with putty knife or flat bar . Roll the gasket toward the inside of frig ,push old holder up carefully out of gasket. Half way out tilt holder back to avoid ceiling . Save old holder for template ,remove screw from bottom,push out rod ,caution clip is spring loaded, install in new holder in reverse,slide back into gasket(carefully)!!replace molding

There is a part called a "cam" on my 23cuft french door refrigerator. It is at the top of both doors and works to keep the closed door from popping open when slamming shut the opposite door. Twice in 2 years this cam has broken off of the long plastic strip which is the gasket holder. Both times on the right door. The repair is easy, but you have to be careful not to break the plastic pieces. First, you have to remove the trim piece covering the gasket strip (233D in the diagram). It pulls out only one way -- toward the SIDE of the door (rather than inwards towards the fridge). Next, you have to remove the entire gasket around the door; it pulls out very easily. Third, there are 2 plastic hinges which snap into the door frame; to remove it use a screwdriver and gently pry it to the side of the door (rather than towards the center of the fridge or away from it). Frankly, that's the hardest part - taking it all apart without breaking the trim piece. When I first had it repaired under warranty, the repairman brought an extra trim piece (233D) in case he broke it when he removed it. But it simply snaps in place so you should be okay if you are careful when prying it out.