All Installation Instructions for Kenmore Range 79094000403

Stove was dropped and had broken, bent frame and adjuster feet

New ones fit perfectly. Take a minute to bend the frame straight. Then and I used oversize screws on the replacement parts as the drop had stripped out the screw holes of the frame.

Parts Used:

Leveling Leg Assembly

Paul from PORT ORANGE, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven bottom panel rusted away

Removed two screws removed and replaced panel.

Parts Used:

Bottom Panel

Ron from CINCINNATI, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

lens was broken

after pulling away from wall and unplugging remove 5 screws in upper back panel lift off being careful of sharp edges if part of lens is still in hole push it out towards the front insert lens from front of unit slide light assy over pin on back of lens replace back panel plug in range push back against wall check for level you're done

Parts Used:

Indicator Light Lens

Kenneth from Coeur d'Alene, ID
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

ugly looking drippans

in order to install the new burner pans, my husband used a screwdriver to push back on the metal clasp. this allows the notch on the drippan to go into the groove on the stove.

Parts Used:

6" FM CHROME DRIP B

Drip Bowl - 8"

Shirley from tulsa, OK
Difficulty Level:
Difficult
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

3 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Replace Element & Drip Bowl

Just replace the parts. Too easy for an old man.

Parts Used:

Surface Element - 8 Inch - 2600W

Drip Bowl - 8"

Fernando from Orlando, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Heavy jam boiler caused elements to sag

Removed the old & simply inserted the new one

Parts Used:

Surface Element - 8 Inch - 2600W

Danny L from CHELAN, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

8" stove top element would not warm up.

It was simple.............the range-top tilts up so I proped it with a stick of wood, pulled out the old burner and plugged in the new one (when I saw how inexpensive the new element was I orderd two to replace the other 8" because it didn't look long for this world either). The whole operation took less than 10 min. no tools or batteries required!!!!!!!!!.........no-mus-no -fus.

Your prices were the lowest I found on-line, keep up the great work!!!!!!!!!

Parts Used:

Surface Element - 8 Inch - 2600W

Margaret from Spencer, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Bottom panel burned through

Remove two back knurled screws, lift out old bottom, screw in new bottom panel. Removal of oven door (two flip out handles at hinge( makes this a little easier. Our oven did not need any other dis-assembly.

Parts Used:

Bottom Panel

Barry from MENDON, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Old bowls were rusted beyond ability to clean

Put the new bowls under the stove top burners with disposable liners to protect them. They look very clean and shiny now!

Parts Used:

6" FM CHROME DRIP B

Drip Bowl - 8"

Shelley from CLYDE, TX
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Terminal block was bad.

Cut the old block off tied new wires to hot wires . That easy!

Parts Used:

Terminal Block Kit

Chuck from EVANSVILLE, IN
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

replaced terminal block for element

followed the video provided on line which was very helpful..

Parts Used:

Terminal Block Kit

Donna from UNION, OR
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Burner element failed

Plugged the new one in and it worked.
I did search out Frigidaire parts and there are other types tha may or may not work. Calrod burners are not all that unusual. I went with the real thing.

Parts Used:

6-Inch Coil Burner Element

Robert from New Castle, PA
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

dead burner

I unplugged the dead burner and plugged in the new burner. Very easy. No tools needed.

Parts Used:

Surface Element - 8 Inch - 2600W

Jan from Storm Lake, IA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

wrong part received and returned

I wanted the bracket for the oven heating element and received the bracket for the broiler.... part returned and now I am stumped about what my next move will be

Parts Used: