79078503013 Kenmore Range - Instructions

I was able to find the most common reason for my oven's symptom by searching online. I searched for the part I needed but was not confident that I would get the correct part until I looked on partselect.com. After verifying the part number with my owners manual and looking at the video on their website, I decided to order. PartSelect shipped the part as expected, and I was able to install it in less than 30 minutes. The only tool needed for installation was a nut driver. My oven is now working like new.

Many thanks to PartSelect for their comprehensive website and fine service.

I changed the temperature sensor and tried again. The stove again went on temp runaway and it was suggested to replace control board which is out of stock.
I will have to toss out this stove and buy new as you and no else has this part.

Went online to find replacement rack. Didn't want to spend the money for a rack I didn't like. Besides the range is 11 years old. Still in great shape. Opted for the simple oven rack.
Open the box and place in oven. Wah lah..
Thank you partselect.com

Removed two screws removed and replaced panel.

Unplugged range; removed back cover; removed old oven probe. Installed new probe; replaced cover; connected power and turned on range - that simple. My only issue was probe was shipped in bubble rap and unit was slightly damaged (bent). Once straightened, the probe could be installed. Probe should have been shipped in sturdy cardboard cylinder or box. I called customer service, they were very nice, and noted my feedback on my account in case the unit fails prematurely.

Removed 2 3/16 bolts and burner, set the oblong burner over the orifice and we were all done

New ones fit perfectly. Take a minute to bend the frame straight. Then and I used oversize screws on the replacement parts as the drop had stripped out the screw holes of the frame.

Remove two back knurled screws, lift out old bottom, screw in new bottom panel. Removal of oven door (two flip out handles at hinge( makes this a little easier. Our oven did not need any other dis-assembly.

I pulled the oven away from the wall, unplugged the cord, removed the back panel then removed the screw from the old sensor.

First, I watched a lot of videos on YouTube. All of them were very similar, and had similar repair instructions, doing all the work at the site of the regulator location. The gas supply flex line was easily detached, as well as the line that exited the regulator to feed the stove. The gas inlet nipple, however, was not willing to unscrew. My regulator was held on by Phillips head sheet metal screws, which were easy enough to unscrew, so I just removed the regulator, still attached to the gas connection nipple. I went to my shop and placed the regulator in a vise, careful to clamp either end, not the regulator valve itself, and used a deep socket over the nipple, and had to use a Breaker Bar to loosen the nipple. I cleaned the nipple where Pipe Dope had been used, and applied new sealant, then screwed it back on the the Regulator, once again using the socket and bar. Then I threaded the new regulator body with the sheet metal screws while it was clamped in the vise. (The new regulator was not threaded, and I had to use vise grips to hold the screws while turning them in) After that, installation of the new regulator was relatively easy. I wish Frigidaire had used hex head screws instead of the Phillips. After install, range worked perfectly. PartSelect delivered correct part in a timely manner.

Unscrew the 2 screws at the back of the oven bottom pan in the range. Place new oven pan in and rescrew the 2 screws. I could not get the two screws screwed back in. Since the bottom pan cannot move from its position, I felt like the two screws were not necessary.

I wanted the bracket for the oven heating element and received the bracket for the broiler.... part returned and now I am stumped about what my next move will be

Pulled oven away from cabinet area
Unplugged oven from wall outlet
Removed screws to free top panel from back of oven
Removed screws to free lower panel from back of oven
Probe backing was now exposed
Unplugged probe from connector
Removed one screw from probe housing
Twisted probe housing counterclockwise then pulled probe out
Reversed the process to install probe
Plugged probe into connector
Reversed the panel removal process
Plugged oven back in to wall outlet
Turned on oven and tested with no further issue

Easy watched on line video

replaced it