79045791103 Kenmore Wall Oven - Instructions

1. Loosened 2 sensor mounting screws and removed them. 2. Tripped range circuit breaker to off. 3. Pulled out the range but left gas connected. 4. Loosened the 4 screws on RH side of the top back panel and carefully pried that side of the panel open. 5. Using fingers, threaded the sensor's wiring harness through insulation and into the oven. 6. Unplugged old probe. 7. plugged in new probe. 8. tugged wiring harness back through insulation behind the oven. 9. Using 2 screws removed in 1 above, mounted new sensor. 10. Repositioned top back panel and fastened it in place. 11. Shoved range back in. 12. Tripped range circuit breaker to on. 13. Reset clock. 14. Set oven to 450 for test tun. 15.

Removed the door from the range, disassembled the door, removed all broken glass fragments, installed the new glass, reassembled the door and reinstalled the door into the range. Straightforward and easy. Keep track of which screws go where and it is a breeze.

Open range door remove 2 screws on bottom of stove top remove top

Turned off electricity to the stove top opened up the aluminum cover under the stove top with the screwdriver Took off the wires one at a time with the pliers as they were on tight and replaced them on the new part Replaced the aluminum cover Turned on electricity and voila it worked fine no sparking

replaced it

Just "locked" the hinges, pulled the door off. Removed the broken glass for the door. Switched the handle from the old door to the new one. thPut it back on e hinges.....viola!! new oven door glass!

Really a no brainer, but I do have to say that PartSelect customer service is excellent. My part was located and on it's way within a day and arrived a couple of days later.

After trying to unscrew a plate on the side, I found that would NOT work at all, the side panel of the stove was behind it. I found a tab that cut-out on 3 sides just above the location of the recepticle, and simply bent that tab out, pulled out the old recepticle, slid in the new recipticle, and put in the screws and then bent back the tab. It was sooo easy once I found that. I repeated in on the other side.

Easy as 1-2-3

Figured out that light and door switch started the convection fan on when door is closed. Found the switch defective. Found exploded view online of switch in oven. Had to figure out that the range top needed to be removed to access the switch from inside the top part of oven. Unscrewed at least (6) screws to free up the range top. Squeezed the inside switch clips to allow switch to be pulled out from outside of oven. Disconnected electrical receptacle and plugged into new switch. Pushed in new switch til it snapped into place. Reinstalled range top.

watched a U-Tube video on this subject.....worked like aa charm!!

Our neighbor, who is an electrician, watched the video on how to install. Since this switch was substituted, he paused the video several times to see how the wires should be attached. It worked.

After removing pots / pans in cabinet below cook top and turning off the power, I was able to remove the panel held by 2 screws. Pulling the old light out was just a little difficult as it came in pieces. New one popped right in, hooked up terminals, replaced the panel and that was it !!

Pull range unit from wall. Disconnect power cord. Remove back panel on range(10 Phillips head screws). Pull knob from surface burner switch and remove two screws. Remove and re-connect wires from switch by number on switch. Replace switch and back range panel. Re-connect power cord and re-position range to original spot.

1. Moved stove from against the wall. 2. Unplugged the power supply. 3. Removed the electrical pannel cover. 4. Disconnected the quick connect probe plug. 5. Opened the oven and removed the probe. 6. Installed the new probe. 7. Connected the quick connect plug. 8. Reattached the electrical panel cover. 9. Plugged in the electrical supply. 10. Moved the stove back into its original position. ****Note**** THIS IS THE SECOND TIME I REPLACED THE PROBE. THE FIRST REPLACEMENT LASTED ONLY 5 MONTHS!!!!