Also known as Probe. The quick connect on this part may be different than your original part. If it doesn't fit, you have to cut off the quick connect and wire together with porcelain wire nuts.
This surface burner element is eight inches in diameter. It has five turns, 2600 watts and looped terminal ends. The element provides heat to the cooking surface on your range. If your element is not ...
This 40-watt appliance light bulb is a reliable replacement for use in select ranges, refrigerators, freezers, and microwaves. It provides bright, consistent lighting to help you see clearly inside yo...
This element has looped terminal ends and comes with a black medallion center. This element is a genuine OEM replacement part, has looped terminal ends, comes with a black medallion center, and fits m...
This broil element is found on the roof of the oven and heats food. The most common reasons you would need to replace this part is due to the oven not giving off enough heat, not turning on, or not ba...
This is a 240-volt surface burner infinite switch for a range or oven. It is for an 8-inch element. This part turns your surface element on and off, and regulates the desired heat of your element. The...
This is a surface burner infinite switch kit for your range or oven. This replacement part activates and deactivates your burner, and controls the burner heat. If you are not getting any heat to your ...
Struggling with an unstable or worn-out oven rack? We have the simple solution to get your oven back to perfect working order - the robust Frigidaire Oven Rack. This dependable part offers a sturdy pl...
No Longer Available
Questions And Answers for 79045482501
Ask our experts a question about this model and we'll get back to you as soon as possible!
1 question answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Robert
February 8, 2025
Stove top heating element gets red hot when set at 7. Is it the element or electrical/switch or something else?
For model number 79045482501
Hi Robert,
Thank you for your question. If you set the burner element to 7 and it goes to a higher setting you will need to check both the element and the burner switch for continuity with a multimeter on the Rx1 setting to see which part is causing the issue. Before removing and checking these parts, unplug the range from the electrical outlet. First visually inspect the element for any signs of bubbling, burning, wear, holes, or damage. If the element is fine, test the element with the multimeter. Touch each of the terminals one at a time with one probe while holding the other probe to the outside surface of the element. If either terminal shows continuity, it is defective. To test the entire element for continuity, place each of the probes on the terminals, one on each. You should receive a reading between 19 to 115 ohms. If you get any other reading you will need to replace the element. For the burner switch, first check the wires near the switch for any signs of burning, or overheated wires and terminals. If there are no visible signs of damage, test the switch with the multimeter. Touch the L1 and H1 terminals with the probes. Once you have completed that test, touch the probes to the L2 & H2 terminals. If your test results indicate that there is no continuity between one or both sets of terminals, you need a replacement infinite switch. We hope this helps!
Replaced clock control by removing surface burner control knobs and plastic nuts, and then the cover over the oven control. Two screw hold the clock in place, after removal and disconnecting the plug-in you can reinstall the new clock control. The Heat Sensor inside the oven will also need to be replaced. It is located inside the oven and attached with two screws; the back of the oven will need to be removed to unplug. Reverse removal procedure and turn the power back on to the stove.
PF alarm appeared on display. Noticed clicking when cord was moved. Had arced for some time and melted original block. New part slightly different. Only has 3 lugs, old one had six. Stack using washers provided. Take note of colors before disassembly. Use caution while working through access opening. The edges are sharp. Only tools needed are phillips screwdriver, deep socket for lug nuts. Nut driver optional. Hope this is helpful.
I pulled my unit out of the wall and noticed that the insulation around the top broiler element was a bit brown. Closer inspection revealed that the element had shorted somehow to the oven itself and caused the element to become non-functional. I tried measuring the resistance first, and it was within typical values for the other elements, but I decided to replace the element anyway.
I ordered from PD and the part arrived just a few days letter by regular shipping. I undid the screws holding in the element, undid the wire connectors and replaced the broken element with the new one. The element worked like a charm and I was back in business for cooking.
