This oven temperature sensor, also known as an oven probe, monitors the internal temperature of the oven cavity to ensure accurate and consistent heating. Measuring 6 inches in length and made of dura...
Struggling with an unstable or worn-out oven rack? We have the simple solution to get your oven back to perfect working order - the robust Frigidaire Oven Rack. This dependable part offers a sturdy pl...
This convection element generates heat to support even air circulation and consistent cooking performance. Its high-output design allows for efficient temperature recovery and uniform results. Replaci...
This bake element provides the primary heat source for baking and roasting in electric and dual-fuel ranges. Positioned at the bottom of the oven cavity, it converts electrical power into radiant heat...
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Joe
July 21, 2023
How to remove the glass stovetop to replace a heating element?
For model number 79041053100
Hi Joe, thank you for asking. Here are some relevant instructions for you to remove the glass stovetop. They may not be of the exact same model, but they will help you with the process. You may follow the following steps: open the oven door and use a flathead screwdriver to help remove the screws securing the top panel. Pull the panel to the front and disconnect the oven control wire harnesses. Remove the screws securing the grounding wire as well and disconnect the surface element wire harnesses. Next, remove the screws securing the bottom of the control cover and set the cover aside. Pull the gasket free of the glass top and remove the screws securing the main top assembly. Note the position of the wire harnesses, then lift the main top assembly up and pull it forward to remove it. We hope this helps, good luck with this repair!
Was this helpful?
Thank you for voting!
Thheresa
April 19, 2024
Looking for a oven Control board with display.
For model number 79041053100
Hello Thheresa, thank you for contacting us. The control board you are looking for is part number PS3495645. If you require assistance to place an order, please contact customer service!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
PF alarm appeared on display. Noticed clicking when cord was moved. Had arced for some time and melted original block. New part slightly different. Only has 3 lugs, old one had six. Stack using washers provided. Take note of colors before disassembly. Use caution while working through access opening. The edges are sharp. Only tools needed are phillips screwdriver, deep socket for lug nuts. Nut driver optional. Hope this is helpful.
This was the first time replacing the fan. It is a lot easier to work in the oven compartment with the oven door removed, only two screws on the door and the hinges were released. I found that a couple of the screws were either rusted or stripped so I used a pair of pliers to remove the screws that were holding the diffuser in place. Once there was access to the fan I found that the fan was warped and that the blades were scraping against the back wall of the oven. The next challenge was to remove the retaining nut. I used a sheet metal screw to secure the warped fan to keep it from spinning. once I figured out that you have to turn the retaining nut to the right to loosen, it came off easily. 1/2" socket with extension. When I replace the fan I used two washers for spacers to make sure that the fan would not scrape the wall of the oven. Its been tested many times and the oven does not make that horrible sound anymore.
Wife was cooking our thanks giving turkey, when an oder of burning was noticed. I walked over to the oven and smelled the area of oven light, it was bad. I turned off and unpluged oven. Got a screw driver, unscrewed 4 screws then noticed the burned switch from under the oven top. removed 3 wires, covered w/ elec. tape, and pulled oven light switch out front. looked at part number and ordered online. We were able to cook our turkey and enjoyed our meal.
