Models > 79031032804

79031032804 Kenmore Range - Overview

Sections of the 79031032804

[Viewing 6 of 6]

Manuals & Care Guides for 79031032804

Click to download
Keep searches simple, eg. "belt" or "pump".
Light Bulb – Part Number: 316538904
Light Bulb
★★★★★
★★★★★
(7)
PartSelect #: PS12751166
Manufacturer #: 316538904
Clear, 120 Volt, 40 Watt.
$25.16
  In Stock
Order within the next 9 hrs and your part ships today!
PROBE – Part Number: 5304525427
PROBE
★★★★★
★★★★★
(19)
PartSelect #: PS16745361
Manufacturer #: 5304525427
$62.29
  In Stock
Order within the next 9 hrs and your part ships today!
LENS – Part Number: 5304524341
LENS
★★★★★
★★★★★
(10)
PartSelect #: PS16218465
Manufacturer #: 5304524341
This lens covers the interior oven light bulb.
$15.70
  In Stock
Order within the next 9 hrs and your part ships today!
RACK – Part Number: 318262516
RACK
★★★★★
★★★★★
(1)
PartSelect #: PS3495822
Manufacturer #: 318262516
$162.96
  In Stock
Order within the next 9 hrs and your part ships today!
Meat Probe Sensor – Part Number: 5304504202
Meat Probe Sensor
★★★★★
★★★★★
(8)
PartSelect #: PS11757868
Manufacturer #: 5304504202
$123.13
  In Stock
Order within the next 9 hrs and your part ships today!
Oven Light Socket – Part Number: 316116400
Oven Light Socket
★★★★★
★★★★★
(5)
PartSelect #: PS439060
Manufacturer #: 316116400
$67.28
  In Stock
Order within the next 9 hrs and your part ships today!
Convection Fan Blade – Part Number: 318398302
Convection Fan Blade
★★★★★
★★★★★
(2)
PartSelect #: PS3409337
Manufacturer #: 318398302
$28.67
  In Stock
Order within the next 9 hrs and your part ships today!
Sealed Burner Head - 14k – Part Number: 316223400
Sealed Burner Head - 14k
PartSelect #: PS820297
Manufacturer #: 316223400
$95.01
  In Stock
Order within the next 9 hrs and your part ships today!
Door Seal – Part Number: 318053120
Door Seal
★★★★★
★★★★★
(2)
PartSelect #: PS978383
Manufacturer #: 318053120
This part has been replaced by the manufacture. It may differ in appearance but will still function the same.
$176.09
  In Stock
Order within the next 9 hrs and your part ships today!
Light Lens Retainer Clip – Part Number: 5304400195
Light Lens Retainer Clip
PartSelect #: PS470510
Manufacturer #: 5304400195
This retainer secures the light lens to the oven cavity.
  No Longer Available
Oven Door Light Switch – Part Number: 316445501
Oven Door Light Switch
★★★★★
★★★★★
(1)
PartSelect #: PS1146808
Manufacturer #: 316445501
$90.90
  In Stock
Order within the next 9 hrs and your part ships today!
Door Spacer – Part Number: 318165800
Door Spacer
PartSelect #: PS978528
Manufacturer #: 318165800
$23.23
  In Stock
Order within the next 9 hrs and your part ships today!

Questions And Answers for 79031032804

Be the first to ask our experts a question about this model!

Common Symptoms of the 79031032804

[Viewing 6 of 6]
Oven is too hot
Fixed by
these parts
Fixing
Show All
Will Not Start
Fixed by
these parts
Fixing Fixing Fixing
Show All
Gas igniter glows, but will not light
Fixed by
these parts
Fixing Fixing Fixing
Show All
Little to no heat when baking
Fixed by
these parts
Fixing
Show All
Oven not heating evenly
Fixed by
these parts
Fixing
Show All
Element will not heat
Fixed by
these parts
Fixing
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven light receptacle broken - bulb base broke off
Turned power off at electrical panel. Pulled oven away from wall. Removed back cover (6 screws), then unplugged wires from old receptacle. I had to pull the squeeze clips backwards & break them to remove the old receptacle - couldn't squeeze them enough to remove them otherwise. The old receptacle came out through the inside of the oven, and the new one snapped in easily from inside the oven as well. Replaced wiring, installed new bulb, restored power & tested. Replaced back cover. Good time to vacuum under/behind where the oven usually lives before sliding it back to the wall.
Parts Used:
Oven Light Socket
  • Paul from Spokane Valley, WA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
64 of 93 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The burner would not light by itself, and the flame was lopsided.
The repair was nothing, but the diagnosis was a bit tricky. After carefully looking at the burner head, (cast aluminum) I pretty much figured out that the 4 small cast aluminum bumps that keep the burner cap positioned up in the air the correct amount to allow gas to flow under the cap, were worn down, preventing the gas from exiting properly by the igniter. My guess was correct. The new burner head solved all my problems. I love Parts Select for the ease of finding the correct parts and how fast they ship their orders. Great company, great service. Keep up the good work
Parts Used:
Sealed Burner Head - 14k
  • Roland from Auburn, ME
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
25 of 28 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
replacing the fan on a convection oven (fan was making a vibration noise)
This was the first time replacing the fan. It is a lot easier to work in the oven compartment with the oven door removed, only two screws on the door and the hinges were released. I found that a couple of the screws were either rusted or stripped so I used a pair of pliers to remove the screws that were holding the diffuser in place. Once there was access to the fan I found that the fan was warped and that the blades were scraping against the back wall of the oven. The next challenge was to remove the retaining nut. I used a sheet metal screw to secure the warped fan to keep it from spinning. once I figured out that you have to turn the retaining nut to the right to loosen, it came off easily. 1/2" socket with extension. When I replace the fan I used two washers for spacers to make sure that the fan would not scrape the wall of the oven. Its been tested many times and the oven does not make that horrible sound anymore.
Parts Used:
Convection Fan Blade
  • John from Stevensville, MD
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers, Socket set
16 of 23 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!