This Refrigerator Air Filter is a white 1.8x3.2" plastic filter which neutralizes odor and bacteria in the air. It should be replaced every six months at a minimum. Refer to your user manual and model...
The EDR1RXD1 water filter uses advanced filtration technology to reduce over 20 types of contaminants, including pharmaceuticals, pesticides, and lead. Certified to meet NSF/ANSI standards, it deliver...
This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
If your refrigerator or freezer is too warm, or making noises, you may need to replace the fan blade. The fan blade attaches to the evaporator motor, which is in the freezer section, to help circulate...
Experience the simple solution to a wobbly refrigerator with the Whirlpool Refrigerator Leveling Leg. This authentic, factory-made part is designed to keep your refrigerator stable and even, saving yo...
Ask our experts a question about this model and we'll get back to you as soon as possible!
3 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Melinda
July 2, 2021
What seems to be the problem when freezer stops working, but blower inside freezer working but not frosting
For model number 6WSC20C6YY00
Hello Melinda, Thank you for the question. We suggest testing the Thermistor, PartSelect Number PS2580944. The best way to do this is to remove the thermostat from the refrigerator so you can control the temperature of the sensor. You can let the sensor warm up to room temperature. With the sensor warmed up to room temperature the sensor should read approximately 6.2K Ohms at 68°F. With the thermistor submerged is a glass full of ice water, the sensor should be very close to 32°F which should read approximately 16.3K Ohms. If the values that you are getting are far off from these readings, then the sensor is bad and should be replaced. Thank you for your inquiry, good luck with this repair!
Still related to freezer problem, I checked that the fan installed at the lower back alongside compressor is not working properly. It functions only from the time you plugged in the refrigerator but once it stops it doesn't go back as it usually does and the freezer will melt. Does it had to do with the control main board installed side to the compressor? I'm clueless because were trying to look into manual of model part but doesn't exist. Please help.
For model number 6WSC20C6YY00
Hello Melinda, Thank you for the question. This normally indicates the Fan Motor will need to be replaced. We hope this helps!
Hi I looking for a Pc main board the part no on the old board is W10235413
For model number 6WSC20C6YY00
Hello Mark, thank you for the great question. The part you are looking for is part number PS11750760. Please reach out to customer service if you need help placing an order, anyone will be happy to assist you!
I used a flat-head screwdriver to pop out the old light rocker switch. Then, I unplugged the wires, plugged them into the new light rocker switch, and then popped the new switch into the hole. That's it! Lights began working again.
An easy job for smaller hands. Removed the two bolts holding the light cover. Removed two electrical connections from the old switch by pinching the retaining clip,removed the switch, snapped in the new one and re-attached the connectors. Your online illustrations helped me to know that the plastic housing for the light switch would only swing down so far and was not intended to be removed. Saved me from breaking that plastic cover's tabs. This home repair saved me more than 5 times the cost of hiring a professional to do it. Very happy homeowner.
When aI received the hose adapter/connector, I inserted the 2 hose ends only to have water drip from the connection. I used a utility knife to remove an inch from each side, then reinserted the hoses. That made the differnce. Dry as a bone.
