6LBR7255BQ2 Whirlpool Washer - Instructions

Followed the excellent video instructions. They say you can perform the repair without removing the enclosure, but when I saw how easy it was to remove it, it definitely improves the access and speeds the repair. Have a piece of wire handy to to hold the pump assembly out of the way. Installed new clutch kit and it runs like a champ.

I watched the videoand just followed your lead. It really was easy. The only thing I didn't have was the agitator grease or lube.

Followed the videos on the website. But had to order parts twice because it wasn't the springs it was the plastic bushings the tub sits on that caused the wobble. No big deal though. All told it was still far less expansive than a new machine.

un-screw old knob with pliers. Hand spin on the new one. Your PartSelect. Is the BEST!!! I ordered on-line Sunday night.Got the part Wedesday!! FAST!!!!!!!

Pulled up on fabric softener dispenser and removed it. Had to use pliers to remove cap and seal to get access to the bolt holding the agitator in.

Realized my socket extension wasn’t long enough so went to Lowe’s and bought another.

Was unable to hold the bottom of the agitator to keep it still and get enough leverage to remove the bolt. I poured hot water over it and then climbed into the washer and used my foot to hold the vanes still while I removed the bolt. Once I got the agitator out, the rest was a breeze. Separated the top of the agitator from the bottom by placing it on the floor, using my feet to hold it down and pulling up to remove the top part of the agitator.
Turned the top of the agitator upside down and removed the cam and feed dogs. Assembled the new one and held the agitator top horizontally while placing the new part back in.
Reassembled the top and bottom of the agitator and put it back into the washer. Tightened the bolt, replaced the cap with its seal and pressed the fabric softener dispenser back into place.

Pulled the machine out. Tilted is back, had my son hold it up. Took pliers pulled off hose clamps, used flat head screw driver to pop off clips. removed pump. Then did it all in reverse.
Piece of cake.

After removing the 2 phillips screws at the base of the control panel, I flipped the panel toward the back. Using a screwdriver, I popped off the spring clips, releasing the cabinet. I removed the 1/4" hex head screw on the spring mount and removed the old spring and replaced with the new. I repeated this with the other 2 springs. The spring bracket in the rear also holds the tub balancing spring. It is easily replaced while replacing the suspension spring.
If this didn't fix the problem, we were going shopping for a new washer. After this repair, it operates like new!

Remove the washer case/enclosure to expose all the internal parts. Lie on the floor and with pliers and a strong arm. Remove and replace each spring one at a time. Pretty straightforward.

First, I read the previous repair stories, so I knew what step to do first. So, first I took the hose off of the drain, then I removed it from the washer. And as the previous repair story stated, some water came out and I had a towel ready to catch the water that was in the hose. I threaded the clamp onto the new hose, pushed the new hose onto the washer, used the pliers to open the clamp to better clamp the hose onto the washer. Then, placed the drain hose into the drain pipe and it was done! Thanks for such a great site!

I did the repairs after watching a few videos on this web site and it covered everything I needed. Went well and the parts were perfect.

Unplug electrical cord, disconnect water inlet hoses and drain line at rear panel. Move washer to garage or larger work area if necessary. Disconnect control panel from top of washer cabinet by removing the two screws at the front corners of the control panel. (The control panel can now be flipped up and back when you are ready to remove the cabinet assembly.) Disconnect the rear panel from cabinet assembly by removing attaching screws at bottom of rear panel (and along the vertical edges if any screws are installed there). Either slightly lift the rear panel up off of the two clip brackets that attach it to the rear top edge of the cabinet assembly, or if need be remove the clips from the cabinet slots. With the rear panel loose, slide the control panel assembly slightly towards the rear and up to disengage it from the cabinet slots, then tip it up and back, away from the cabinet. The cabinet assembly (with top attached) can now be tipped forward and away from washer to expose the internal workings. (It may be necessary to support the rear panel and/or control panel.) The water pump is attached to the front of the motor by two spring clips. Disconnect the two water lines from the pump, then remove the two spring clips. Pull the pump forward off of the shaft extending out of the motor. Install the new pump, then assemble the washer in reverse order. (I was unsure where the leak originated on my washer so I completely removed the rear panel which entailed disconnecting from it the electrical cord fitting, drain and input water fixtures and various other brackets. Pump replacement can be accomplished without completely removing the back panel.)

Followed the video on the website. I removed the hoses from the pump rather than removing the pump as suggested in the video. Then separated the motor from the transmission and replaced the coupling; then reattached the motor and hoses. Lining up the washer cover and clamping it back on was the most trouble. But all in all, a easy repair.

diconnected water supply and discharge, unplugged the unit, removed the aggitator, laid the washer on it's back, romoved the hoses from the pump, took out 3 bolts, removed the motor/transmission and replaced the clutch and put it all back together.

just like video showed really helpfull

A label was created and never shipped. Sat there for 2 weeks.
Contacted company for a refund and a Retha’s never been issued.
Terrible service!