6GD5SHGXSS07 Whirlpool Refrigerator - Instructions

I just followed the excellent Video for both parts. The door gasket is tedious but doable, just take a deep breath and press on. Putty knife is handy to push edge of gasket under the plastic lip. The closer devices take 3 minutes - simple R&R. Check the videos - they're pretty clear and detailed.

Pulled old ice tray out, dumped ice into new tray, inserted new tray

Took the old Ice Container and Auger Assembly out and tossed it in the trash...washed and dried the new Ice Container and Auger Assembly placed it in designated area and I've been having crushed ice ever since!

easy - remove the door, replace th part, put back the door

Undo a few screws on top of door, replace closing washers at bottom part of door, put door back on, and done. Easy. Just make sure you have the top and bottom closer washers that go together...2 parts.

Just clicked it in place and was done in less than a minute. Thanks for the fast ship and right part.

Simply remove the cover over top hinge and remove the three outer screws (Do NOT remove the center screw). Lift the door off the lower pivot pin. Turn door upside down and replace the upper cam and then the lower cam on the pivot at the bottom of the refrigerator case. Reintall the door by setting the door on the lower pivot and then reinstall the top pivot and cover. VERY easy and what a difference. No more "POP".

Purchased the closing cam (both pieces). Removed door (3 bolts under the dust shield on top of door) and replaced the plastic cam pieces. So easy a caveman could do it. I actually had my 13 year old son do it while I supervised!

I did some tests and determined that the tub-to-pump drain hose had a leak in it.I then looked on the web to find disassembly instructions. I have a stacked washer dryer combination in a very confined space. The repair involved disconnecting both the washer and dryer from the water, gas, electric and venting systems first, then unstacking the dryer from the washer (not so easy, it required a helper). The machine was then pulled out so I could get at the parts necessary to remove the outside components and sheet metal. Then, I disassembled the top, front and access panel in the back. The disassembly went very well. I got access to the drain hose assembly and removed it fairly easily. I ordered a replacement drain hose assembly and found that installing the large port of the assembly was very difficult. (The two other ports were easy.) After thinking about it, I tilted the machine back a bit so I could try it from the bottom. That worked fine.I then reassembled and tested the machine. No leaks. Good luck with yours!

Ordered Ice Bin Auger and changed with no problem. Found how to change on YouTube and followed video.

remove top hinge take door off replace parts on bottm hinge put door back on done

After fabricating a new part to hold the spring rod in place, so the dispenser flap would close tightly in place. Every thing else to reassemble was very easy.

I followed the instruction video and it is very straight forward. My biggest problem was disconnection the 2 tubes that insert into the filter holder. Once I disconnected it from the front, I couldn't pull it far enough forward to get good access to manipulate those tubes. I had to pull the refrigerator out from the wall to get access to the back. On the back, there is another part you can unscrew where the other end of the tubes are connected. Once you've done this, you can pull the filter holder forward and release those tubes. Then attach the tubes to the new filter holder and reinstall everything.

Just as shown on your video.The refrigerator side was not sitting even, clunked and did not seal right. I decided to do.both sides, refrigerator and freezer while I was at it as our refrigerator is about 16 years old. Everything went in easily and saved us a lot of money. Very happy with the parts and repair video. Got the refrigerator nice and cleaned out while we were at it..Us and the refrigerator are breathing easier now..Yeepppeee....

The repair went pretty easy. You must remove the cover and lift up the electronics to gain access. The instructions were a little vague since the new door/chute didn't have the electric heater wire. I eventually realized that it wasn't needed and replaced the door without further incident.

With a new valve in the back, I now have water and ice at the door after a couple year hiatus!

Thanks.