66598003701 Kenmore Range - Instructions

Put the back of stove on blocks of wood to get high enough to screw the new leg in.

1. Turned off the electrical power. 2. Removed 4 philips head screws two from hanger bracket two from oven burner. 3. When hanger bracket screws are removed the bracket can be slid forward off the burner element. 4. When the burner element screws are removed the burner can be pulled forward where the wires can be removed (they are push on connectors)I did not need pliers but you may need them to assist you. Make sure the wires don't fall down into the oven holes. Reattach wires to new burner. Reattach burner to oven rear wall. Reattach hanger bracket. Turn on the electrical power. Broil your self a steak for a job well done.

This was the easiest repair I have ever done. The element was shipped right away and I received it in about 3 or 4 days. 2 screws were removed and reinserted to replace the heating element.

turned off the oven at the main breaker. removed the four screws...two in back and two on the upper holding breacket.
removed the element and disconnected the spade contacts by just pulling them apart. measured it. Compared measurements
with items in catalog. Found exact match, ordered it.
Put it in same as out only reverse.
easy.

I removed the two screws retaining the heating element with a phillips head screw driver. Then I pulled the element forward to expose the wire connectors, and disconnected the two wires. I connected the two wires to the new heating element, and secured the new heating element with the two screws.

easily pulled old seal out and push new seal in place simple and quick.

It's a straightforward remove and replace with two screws. The lower element is most likely to go with years of baking when bake pans overflow on to the element, It can be checked with an electrical probe for resistance and continuity. If the oven is preheating and the lower element doesn't heat that is definitive. We had it checked under the extended warranty but the tech wasn't thorough enough. The extended warranty is of questional value.

removed stove/oven back & disconnected 2 wires. Removed 2 screws holding element to back of oven & 2 screws holding retainer bracket. Replaced element reversed procedure.

Took 5 minutes... I did it in my pajamas... after a heavy duty margarita!

Here's a tip: start from behind.

Unplugged the oven range, it is a dual oven. Removed the 2 screws in the back to loosen the element. Removed the 2 screws that held the bracket that held the element. Removed the 10 screws in the back that holds the back panel and then disconnected the cables to the element. Installed the element in the reverse. Easy.

The repair is only half the battle... for hands-on homeowners.

The repair went very well! Not only was the clear speaking PERSON on the phone extremely helpful, we saved MONEY, functional DIAGRAMS on the web to assist in finding the part you need, the part was DELIVERED in a timely manner, directly to our home.

Before I found PartSelect; I fought mandatory email inquiries for the part, proposed in-home service visited scheduled sometime between 8-5, unrecognizable speaking person… these issues left me rubbing my head to soothe a headache that had just started and the part had not even been ordered… Anyone will look back on their experience with PartSelect and feel they have just returned from a wonderful restful vacation. THANKS!

4 screws, removed old element and installed new.

Unscrewed two screws on oven’s back wall holding the element. Unscrewed two screws to remove element retainer from top of oven. Disconnected the wires from the defective element and connected to new element. Placed new element and tightened screws holding it to oven’s back wall and placed retainer on top of oven.

Once I saw the spring clips on the new door seal, it was easy to understadn how to remove the old seal and install the new one. Looks nice !

I unscrewed 4 screws. 2 held the element into the back of the oven and 2 held a holding bracket to the top of the oven. I pulled the old element off the two wire brackets coming out of the back wall of the oven. Then I took the new element and reversed the process. Easy.