6654558990 Kenmore Range - Instructions

Unscrewed the two screws that held the old element to the back wall of the overn. Pulled out to reveal the two wires and connectors. Disconnected the two wires and removed old element being careful not to let the two wires recede back into the wall of the overn. Took the new element and connected the two wires. Then screwed the two screws through the holes in the element into the back wall. Easier than I thought it would be.

I removed the two screws that hold the element in place and then I pulled the element out and slid off the contacs and it was disconnected in less than two minutes. When it arrived I installed the new one the same way in less than 2 or 3 minutes and while I waited for thepart to arrive I got a chance to clean my oven and so all is well, I am very pleased with my purchase. It is just that easy and I am happily baking again. Thanks, j. Cale, morrow ga.

My handyman removed the old burnt our element by removing two screws and disconnected two wires and reconnected wire and screwed the unit into the oven wall. This repair was a breeze! Thanks for making my life easier!

Replaced broken element with new one, part was delivering quickly and work great

I unplugged the stove/oven then unscrewed the bottom element (two screws in the back). I pulled the two electrical clips off the old bake element then removed it. I pushed the electrical clips on the new back element then screwed it back in. After plugging the oven back in and turning it on the oven worked perfectly!

I ordered part from Part Select, which literally arrived in 2 days. I unscrewed the two (2) screws holding the old bake element in the oven. Pulled out the element and detached the wires connected to the element, which was easily done without any tools. Attached those wires (again easily by hand with no tools) to the new bake element and screwed the two (2) screws back in. The whole process including ordering the part online, unpacking the box and installing took 15 minutes. Wonderful and in time for my wife and daughter to bake Christmas cookies!

i received the part via fed-x i opened the box uninstalled the old part installed the new part turned it on the element got red hot and it works just fine.

I order the part on 7/29 and much to my surprise, it arrived the very next day. It took less than 15 minutes to remove the old element and installed the new one. It was a little difficult to unplug the old one and took quite a bit of pulling but it came out okay. Plugging in the new one and screwing on the cover plate was easy.

Shut off circuit breaker to stove. Removed oven racks from oven. Removed two phillips head screws located at the base of the bake element at the back of the oven. Gently pull the element toward the front of the oven until the wiring connected to the element by spade connections can be reached. I used a pair of pliers to help separate the element from the wiring. Removed disfunctional element from oven. Sweep out the bottom of the stove with a dustpan & brush. Lay the new replacement element on the bottom of the oven. Connect element to wiring via spade connectors. Gently feed the wires back thru the holes until the the tips of the element follow thru the wire holes until the base of the element is flat against the back of the oven. Screw in screws thru the base to the back of oven - tighten tight. Reset cir brkr. Test oven.

Replaced for a friend who was financially unable to purchase the unit. Turned off power to stove. Removed two screws. Inserted the unit and replaced the two screws. All fixed in about 15 min. Now she can enjoy baking again.

Shut power off to stove, by turning off breaker. Using a screw driver, removed the 2 screws securing broken bake element to back of oven wall. Grasp the 2 wires holding the prones & gentley removed broken element. Attached new bake element to wires, put screws back in & secured to oven wall, turned breaker to stove back on. Oven works great, had pizza for dinner.

I removed the screws that hold the element in place .
Pulled the element out enough to disconnect the two wires . I then connected the new wires and pushed in the element . I finished off by screwing the bolts back in place.. Voila!!!!!!! I was in business once more!
The part arrived within 48 hours and was very reasonably priced

followed the instructions. removed the old element and installed new one.

Unplug power cord, remove wires from block. take 2 screws out. replace with new block about 15 mins. Done

i removed the back cover unpluged 2 wires
inside the oven removed 2 screws from the element . reversed the process to re install the new part