6654433451 Kenmore Wall Oven - Instructions

turn off electric breaker, unscrew the 2 screws unplug the 2 ends replace old element with new repeat previous steps but unfortunately the control panel was also failing and that item has been discontinued.

replaced light socket but did not repair problem. must have burned the motherboard.


pleased with service from your company.

I'll tell you.......PartSelect said the items would take from 3-5 days.....I got them in 48 hrs. I turned the breaker to the oven off. I unscrewd two screws from the back of the oven and pulled the element out and took it off of two connectors. Repeated the same with the broiler element. Job done saved $200.00...Job was quoted at $259.00

First, I removed the oven door by pulling it open to where it loocked and then I pulled it up and off the hinges. Second, I removed the two screws on the top of the door and three screws on the bottom ot the door which allowed me to remove the front of the door. Third, using a nut driver, I removed the frame holding the inner glass to the door and removed that. Fourth, I removed the frame holding the broken glass to the door by removing the screws using my nut driver. I carefully removed the broken glass and vacuumed the channel that had the gasket in it. The gasket was fine so I did not have to replace it and will return it. I placed the glass in the frame on the gasket and reassembled the door in reverse order of how I had disassembled. All went smooth as silk.

The hardest part was figuring which breaker controlled the oven because it wasn't marked in my breaker box (it IS now!). So, first I killed all power to the stove, then unscrewed the 2 screws in the back of the oven holding the element. Pulled the element forward, then dissconnected the 2 clampy connector wires (yes, I'm a girl, no correct electrical jargon here). These were a little difficult because my oven is 21 years old & this is the first replacement I've had to do. I reconnected the new element clamps(which was easier), pushed the wires back through the opening & reinserted the screws. Threw the breaker back on, turned on oven to 200 degrees & let heat until the set temperature light turned off as a test. Voila - oven fixed!

When we received the part, it had an extra little tab on it which had no place to fit in our microwave. We were able to saw the extra tab off, place it (with the spring) in the opening, and it worked!

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

We have had our Whirlpool oven for 22 years and became very concerned that a part would not be available. We were thrilled to find the part as well as install the new part ourselves. With a screw driver, we disconnected the old baking element ( be sure to shut the power while doing this) and screwed in the new one. That simple!!!

I had no instructions, so I started by removing the two screws that seemed to hold the element together. I pulled the element forward and realized I had to seperate the element from the wires. It was an old unit so it took a strong tug but it did come apart. I was hoping at this point I was doing the right thing...I reconnected the new element , pushed it back in and replaced the screws. I was very impressed with myself! The new element heated up in no time. Yeah me!
Thank you "Part Select" for making it possible.

I took out 2 screws and installed new element! It took 5 mins.

Well it was quite simple to replace all I used was a long Phillips screw driver,the job only took me 10 minutes to complete,thank you so much for the part you sent me it was the correct part.

It was so easy. I removed the baking racks. Then I unscrewed two Philips head screws that held the rack in place. Then I pulled the two connections apart from the wiring. Plugged the new element into the wiring. It was as simple as sliding it in and out, replaced the screws, and within minutes I was back to baking again.

First I removed the two screwes that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires from the old element, then I connected the two wires to the new oven heating element. Pushed the unit back in place and reinstalled the two screws that hold it in place.( ALL Done)

simple replacement

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...)