66516517990 Kenmore Dishwasher - Instructions

Simply removed deflectors and gasket, replaced all , took all of 5 mins. workes great now.

Installed the new upper spray arm mount. First I installed it backwards which made the blades not turn freely (rub against top rack basket). Turned it around and was good to go. I found it helpful to remove the top basket in order to do this. Note that this clip is gray while your dishwasher tines are white. This does not cause any harm.

I ordered both the front control panel assembly and the electronic control board, more or less knowing that one of these two items would fix the problem. I felt it was more likely to be the front panel, so I replaced that first.

To do so, I removed power from the dishwasher, removed 8-10 torx screws to remove the inside panel of the door. Then I disconnected all of the wires connected to the electronic control board because it is attached to the inside of the front panel assembly. I marked the positions of the door switch wires so that they could be replaced in the correct positions. Once the wires were detached, the control board could be removed by pressing on a tab so it could be lifted off. The hardest part was removing the front panel itself. Because the dishwasher was black, it was really hard to tell where one part ended and another started, but essentially the panel snapped out by pushing on the top from the inside of the door. The panel eventually pivoted down and became free to lift off of the door.

Reassembly with the new panel went just as smoothly. The hardest part was working the new panel into position so that it would snap into place. Once in position, it was a simple matter to re-attach and connect the old logic board, it's wires, the door lock, and the inside of the door.

Testing after restoring the power showed that the front panel did the trick. Since I had never taken the control board out of the box it was shipped in, I was able to return the unused part.

Plastic parts on this Kitchenaid dishwasher suffer repeat wear problems from heat and chemical detergents. The retainer nut on the bottom wash arm split horizontally int the thread area, and during operation, the wash arm would rise up and hit the bottom of the lower basket so there was a worn groove in the wing on top of the nut and the dishes weren't getting very clean. Simple replacement, just screw the nut down. Also decided to replace the bearing ring right under the wash arm because it was getting pasted with white crust-like material from hard water and chemical detergent residues. I've dealt with PartSelect twice now, and they are fast and efficient. The online parts breakdowns are easy to follow.

unscrewed sprayarm, removed bearing and seal, used PartSelect pic and description schematic to identify part numbers then placed order. Parts arrived in two or three days.

Removed upper basket and installed the arm. New snap in didn't require phillips screwdriver as old one and new support had split to insert. Replacing upper spray spinner dropped screw down around pump. This caused misery unassembling lower covers to receive Stainless
Steel, so magnet won't help ended up with mirror and hemistat to reach through large screen figures. So make sure to put towel or something in the bottom to catch parts.

Bottom wash arm bearing and seal were severely worn and leaking. Replaced in about one minute with new parts from PartSelect.com, and took the opportunity to clean out the arm -- stringy, fibrous matter was clogging two jets.

Top arm horizontal rubber supply tube was disintegrating and leaked. Replace with Spray Arm Kit -- this took maybe two minutes!

Lastly, two to of the upper right-rear folding rack tine clips were broken -- replacement was difficult as the old, broken clips were very stiff and came off only after much physical persuasion! New clips were installed easitly -- in a "snap". Time ~ 5 minutes.

Best of all, the new parts were delivered to my home within 36 hours of my internet order. I thought the prices were fair, too. Thanks.

Replaced the middle spray arm kit and the upper spray arm mount. Also replaced worn out spring for the soap dish.
Now all areas of the dishwasher get cleaned and the soap dispenses correctly every time.

The old tine row came out easily and the new one was easy to pop into place. I was pleased that it was so easy to order a replacement part.

Removed one screw to get the spray arm off the rack, one other screw to disassembly the spray arm assembly. Replaced worn and damaged parts. Installation was reverse order of disassembly.

Removed the rest of the broken retainer plug. Part number was on the top of the plug. Went to Partselect.com looked up the part and ordered it. The right part (important) arrived in a few days. I put the arm back in place, screwed in the new retainer plug and we were back in business. Cost of part about $5.00. Price of not having to share in cleaning the dishes, priceless. Any future problems with any of my appliances, this is the first place I'll look for the needed part.

I removed the screws on the door cover and snapped in the new clip

for the arm I just removed one screw and replaced the arm

There were two somewhat difficult parts: identifying the correct clip (first time I got it wrong and had to reorder), and attaching the new clips in the proper orientation without breaking them.

The correct clips have a snap-in feature to hold a wire fence upright. Two tines of the fence snap into the clip, which attaches to the lateral wires in the upper basket.

To remove the broken clips, I pressed the flat blade of a large screwdriver against the open side of each, noting which wire each came from. I measured the distance between the two wires for the next step.

To install the new clips, I first attached them to the moveable fence. This is because (1) the clip has extremely complex geometery and it took a while to figure how it should be installed (I had no model because the old clips were completely destroyed) and (2) the notch for the fence is quite rigid on one side, and quite delicate on the other, and it took a bit of force to get the the thick bottom wire of the fence to seat properly without breaking the delicate part of the clip. There is no way to put the fence into the clip if you have first installed it onto the wire basket without breaking the clip because the beefy side is not flexible. I used the flat blade of the screwdriver on the beefy side and pinched the bottom of the fence into it with my thumb.

Each clip must straddle one of the tines of the fence, so the tine can swivel into the upper part of the clip to stand upright. This is definitiely a spatial relationship challenge and it took a few minutes of trial, error, and visualization to figure out. You must also be sure that the tines you select correspond to the distance between the two locations on the wire basket where they will attach.

Once the clips were on the fence, I rotated the fence so that the tines locked. Then I attached the clips to the basket, using the flat of the screwdriver blade and a steady pressure to snap it on.

Removed old phillips head screws /w washers from spray arm kit and mounting bracket. (You'll need to keep one screw/washer set.) Attached new mounting bracket and screwed securely. Attached spray arm with new screw/washer and I was good to go. Piece of cake!

replaced spray arm, but this did not resolve the problem. The troubleshooting guid (inside kick panel) indicated the check valve may be stuck. We had quite a bit of lime build up, so I suspected the loose deposits may be stuck. I removed all of the deposits, disassembled the lower unit.
Removed lower spray arm, removed spry tube. The tube is two pieces. first the upper portion must be removed (two screws-place towel on base of tub to preven screws from falling into the chopper area), and then the lower portion simply rotates clockwise 1/8 of a turn. The attachment for lower spray arm has a small plastic bearing, careful not to drop it.
The dishwaser then had to be pulled out and turned on the side. I removed the entire lower unit by removing the white tabs (3). Careful, because the unit is now free to drop into the tub. Next I removed the pump. This is tricky as you have to remove the aluminimum bracket to get to the mountin bolt. The bolt turns out easily w/socket and extension. The pump motor is then rotated counter clockwise, and pulled from the pump. Takes a little force as the gasket makes for a tight fit.
I then removed the choper / pump unit from the basin. The build up behind the chopper screen was extensive, so I had to remove the screen and then the chopper cover. After cleaning, the check valve was unplugged and I reassembled the unit.

Dishwasher works great now.