66515973992 Kenmore Dishwasher - Instructions

Turned off the power, just to be safe.

Removed the lower panel (4 screws). That made it easier to remove the lower 2 screws on the door panel. Slid the panel down slightly, then pulled off.

Removed the old dispenser - disconnected 2 wires, removed 6 screws, pushed in the plastic clips.

Pushed the new unit into place - clips click in. replaced 6 screws and 2 wires. Put the panels back on. Power on.

About 25 minutes.

The video offered was perfect and walked me through the exact process and gave me the confidence i could handle this repair myself. It was very intuitive and went step by step. Thank you for taking the time to post the repair steps on video. Ordering the parts was very simple and they arrived on time. Flawless in every aspect. i would recommend your company.

Turned of water and unplugged the dishwasher.
Disconnected the incoming water line.
Drained on to the floor (have paper towels ready)
Disconnected the electrical feed wire.
Disconnected the rubber hose.
Unscrewed screw holding the fixture to the frame.
Took off the brass elbow from the old part.
Put pipedope around it and screwed into new part (carefully, so as to not crack plastic again).
Attached part back to frame.
Attached water lines.
Turned on water, plugged it in and ran dishwasher looking for leaks. No problem.

First turned off the power at the breaker box. I removed the screws on the inside of the dishwasher, then took off the front touch pad control panel. Removed the old fuse, tested it, orderd a new one. Left the DW dismantled while I waited for the new part. Then put it all back together. I have also replaced the latch on this same DW, but they were both pretty easy.

Was able to replace and repair without taking the dishwasher out. Thermostat is behind and to the left of the power junction box. Has 2 wires going to it. It is up against the bottom of tub. I used an angled mirror to see what I was doing. 1 small screw to detach and pull down thermostat. Be sure power is off before you start. Also reprogrammed defaults. Hit any button 1-2-3, 1-2-3, 1-2-3, fast and close door. Let it sit 15 min to run and re-set defaults. Now I have heat and dry dishes.

This part is different than the original but works great. I used Geronimo's instructions, but cut the ring (see below) so I didn't have to glue it back together.

1-remove upper rack by removing holding clips.

2-remove old assembly from Rack

3-Use exacto knife to cut old ring guide at top between 2 hooks to accommodate new style (one solid plastic piece). No need to re-glue since the hooks hold it up okay.

4-re-install upper rack

First of all, we were very impressed with the ease of finding the parts, the ordering, and the velocity in which the parts were shipped. We received them the next day. I had to remove one of the screws from the old kit, since the new one only came with one. I looked at the diagram on the website of the assembly, and also remembered what the assembly looked like before I took it apart. The first time I tried it, I could not get the spray arm to spin without hitting the dishwasher rack. Since I had ran out of time, I had to wait until the next day. Once I started, I realized that I had the mounting bracket on backwards. Once I turned it around, I tightened the screws, and it was done within 5 minutes.

I unscrewed the old water inlet valve from the frame of the dishwasher so that I could manuever my hand around to the backside where the rubber hose was connected. That was the easy part. I then had trouble holding the old valve while trying to unscrew the hot water copper tubing so I screwed it back on the frame. My dishwasher is close to 18 years old and I think that was part of the problem. After soaking in WD40, I finally got the valve out. Then I had to remove the "L" shaped connector to put on the new valve. Everything went back together a lot faster and it's like I have a new dishwasher again. By the way, I am a 53 year old female so that may be why it took me so long.

Removed 5 or 6 screws replaced O ring,Srewed cover back on ,no more leak.

Removed dishwasher, take to garage, removed lower rack to gain access to top of motor unit. Used star socket wrench to remove upper screws holding top of unit in. Disconnect wires, drain tube and counter weight. pulled motor unit out from inside dishwasher and placed on bench. Proceeded to disassemble motor. Some things were obvious, others not so. replaced old worn out parts with new, used a little lube (Vaseline) in places to assist in getting seals back in place. Instructions were of little help need to pay close attention when tearing unit apart. Reassembled with new seals, installed motor and re-installed dishwasher...NO LEAKS!! Wife and I happy.

The dishrack fits perfectly in our 10 yr old KitchenAid dishwasher. Took a little while installing the wheels and 3 rows of tines that were not in place as instruction sheet was a bit vague. Our old rack had had several tines rust off, and recently learned that we should be using liquid detergent as the powder is like a sandblasting agent over time. Also we didn't get a knife/fork basket with the rack; however, old one fit okay.

One day the door came slaming down. Pulled off the bottom two panels and noticed a broken spring. For the small investment I purchased two new springs and replaced both while I was down there.

1) Pulled off the bottom two panels
2) Took note of location of where the springs were and removed the old springs.
3) With my fingers found the holes and placed new spring on the door side.
4) With some muscle stretched the spring untill it joined the multiple tension slots on the frame of the washer.
5) Found the correct tension to suppt the door opening and closing properly.
6) Replaced the two bottom panels
7) Cleaned up and was done!

Thank you partselect for your great web help!

Took off the front cover and scraped out soap deposits - probably consequent to wash water not being hot enough. Replaced the lower seal - used some automotive weatherstrip seal to cement it in place. Loosened the door per instruction sheet and replaced the water deflectors on each lower corner. Probably took me longer since I'm 81 years old and don't get up and down as well as I once did. Insulated the hot water tube so wash water is hotter than before. Works pretty good.

No brainer

After pulling the dishwasher out from under the cabinet, I found it underneath near the back right side. I disconnected the old thermostat, unscrewed the clamp holding it into place, put the new thermostat in, screwed it back in and replaced the two plugs. Then I pushed the dishwasher back into place, and it initially didn't work until I found an online forum that was able to identify the reset command for my dishwasher (for the WDT710PAYM4, press any three buttons in a sequence of 1 2 3 1 2 3 1 2 3. After completing that all the lights lit up, and I shut the door leaving it for half an hour) Once the reset finished, the heated dry worked like it was suppose to.