66515914000 Kenmore Dishwasher - Instructions

PartSelect found the right part for me on the first try. I had scoured the web looking for this particular drying agent cap. Even Sears said I'd have to order the entire dispenser assembly - $$$!

PartSelect found just the cap I needed at a much better price.

Fantastic service. Shipping was faster than promised. I can't say enough good things about them!

put new hose on, very easy.

Remove 2 screws on lower baseplate. Remove 2 screws that hold dishwasher inside cabinet( may be attached to counter top or side cabinets). Turn off water supply to dishwasher. Remove any connections such as water supply, electrical connection, or waste water line that prevent dishwasher from being pulled out about 3/4 of the way. With the dishwasher door closed, remove broken parts and replace with new parts. Pull on spring to make final connection of nylon cable. Reverse the above instructions for re-installing the machine.

Removed the old tines by pushing out the clips on the end and then installed the new tines and applied clips - took 10 minutes worked slick and the washer basket looks to be brand.

1. Opened inside panel (about 8 screws)
2. Checked wires to see if we had power, which led me to the fuse.
3. All wires were hot, so I bypassed fuse straight to the motor, which worked.
4. Took out the fuse, didn't really know for sure whether it was bad yet, googled the part number and it led me to PartSelect.com!
5. Ordered part (it arrived in two days!) and replaced existing fuse and WE ARE WASHING DISHED AGAIN!!

Replacing the float switch was fairly easy and straight forward. removed old using adjustable wrench and replaced.

Replacing the door links was not difficult except I needed to pull the dishwasher out and had to disconnect the water line.
reconnecting the water line was the time consuming and frustrating part. Once that was hooked up and tested, i pushed the dishwasher back in place and all is good again.

Remove the mounting screws that hold the dishwasher under the counter top. Remove dust cover plates at the bottom of the machine. The machine will have to be pulled out, so turn off the water to the machine. Usually under the kitchen sink. Disconnect water supply and push it out of the way so the dishwasher can be pulled out. Pull machine out enough so you have access to the door cables and springs. The door will have to be in the closed(up) position to do the repair. Usually only one side is broken. Start with the broken side and copy the working side when installing new parts. Then repair the working side. To get the working side apart just pull on the spring and disconnect it from the cable. Do the reverse to reinstall.

Hardest part was pulling dishwasher away from cabinet, making sure to not disturb water and drain line. I replaced both door springs which are on the two sides and attached to the dishwasher frame towards the back. This necessiatated pulling the dishwasher about 2/3 out of cabinet. After attaching both springs to frame, replacing the balance kit was a breeze .One screw to remove and then replace with new pulley unit. Attach the supplied cord with attached fittings to spring and then around two pulleys and mounting point on frame. Done . Push dishwasher back into cabinet, reattach two screws to underside of counter. Probably did not require new springs as they seem heavy duty and were not broken upon examination but ordered them also and replaced just in case. Most problem would be with broken cord in balance link kit

Snapped the new stops on. It took about 2 minutes.

Removed old part and replaced with new part

Removed old tine rows and replaced with the new parts. No tools were needed. Each was replaced one at a time so the old ones could serve as a model for how the new ones were inserted and attached. Not much more complicated than changing a light bulb. Parts appear to be good original equipment quality but quite pricy for these very simple pieces.

Removed the old hose, after loosing metal looking rings. Installed new hose ad finally tight firmly the looking rings, using wrench and socket.

After researching the issue, it pointed to either a clogged hose or a bad pump. I cleaning the hose, verifying that there was no clog by using baking soda, vinegar and water. It would work, once maybe twice, then the water would sit again. I checked the line again, no issues. I purchased a new pump. The installation of the pump was easy, only to discover that this did NOT solve my problem. I am now considering a new dishwasher or purchasing a new $150 motor. It sucks not being able to send the parts back.

Loosened 1 screw to access spinner button. Removed broken spinner button, replaced it with new button,snapped spinner and wedge on button ,replaced screw and was done in about 2 minutes. Thanks for the pictures of installation and the quick shipping of parts. Not to mention the money saved by doing it without a repairman. Thank you

When my dishwasher stopped working I went to the local appliance parts store with the entire button panel. I explained my situation to them, and the response was that I needed a new control panel -$68 and a week wait. So I ordered it. When it came in I noticed it was missing a button for the rinse only cycle. The parts guy said that maybe it was a problem with the parts vendor and ordered another one from their other vendor. In the mean time I installed the new control panel just to see if I would get any lights (no luck). A week later the new control panel came in - still no rinse only button. I got my money back and went home to see what I could find online. I ran across PartSelect - saw several comments describing my exact problem, and ordered a new fuse kit ($15). I put the original control panel back in, put in the new fuse (which took only 2 days to get to me!) and sure enough - problem solved.
Thanks PartSelect you have a great site with lots of useful information!

Steve in Colorado