66515897990 Kenmore Dishwasher - Instructions

Simply removed deflectors and gasket, replaced all , took all of 5 mins. workes great now.

The old gasket came out easily, but had calcium deposits in area. I cleaned the area with vinegar and water and waited until it was completely dry. The new gasket went in very easily and looked great. I started the dishwasher and alas, it still leaks, so the problem was apparently not with the gasket, but some other area. But the gasket is nice and new. Any suggestions on next step0 in troubleshooting?

Installed the new upper spray arm mount. First I installed it backwards which made the blades not turn freely (rub against top rack basket). Turned it around and was good to go. I found it helpful to remove the top basket in order to do this. Note that this clip is gray while your dishwasher tines are white. This does not cause any harm.

Plastic parts on this Kitchenaid dishwasher suffer repeat wear problems from heat and chemical detergents. The retainer nut on the bottom wash arm split horizontally int the thread area, and during operation, the wash arm would rise up and hit the bottom of the lower basket so there was a worn groove in the wing on top of the nut and the dishes weren't getting very clean. Simple replacement, just screw the nut down. Also decided to replace the bearing ring right under the wash arm because it was getting pasted with white crust-like material from hard water and chemical detergent residues. I've dealt with PartSelect twice now, and they are fast and efficient. The online parts breakdowns are easy to follow.

Removed upper basket and installed the arm. New snap in didn't require phillips screwdriver as old one and new support had split to insert. Replacing upper spray spinner dropped screw down around pump. This caused misery unassembling lower covers to receive Stainless
Steel, so magnet won't help ended up with mirror and hemistat to reach through large screen figures. So make sure to put towel or something in the bottom to catch parts.

Bottom wash arm bearing and seal were severely worn and leaking. Replaced in about one minute with new parts from PartSelect.com, and took the opportunity to clean out the arm -- stringy, fibrous matter was clogging two jets.

Top arm horizontal rubber supply tube was disintegrating and leaked. Replace with Spray Arm Kit -- this took maybe two minutes!

Lastly, two to of the upper right-rear folding rack tine clips were broken -- replacement was difficult as the old, broken clips were very stiff and came off only after much physical persuasion! New clips were installed easitly -- in a "snap". Time ~ 5 minutes.

Best of all, the new parts were delivered to my home within 36 hours of my internet order. I thought the prices were fair, too. Thanks.

unscrewed sprayarm, removed bearing and seal, used PartSelect pic and description schematic to identify part numbers then placed order. Parts arrived in two or three days.

The old tine row came out easily and the new one was easy to pop into place. I was pleased that it was so easy to order a replacement part.

Pretty simple. Hardest part was working the end clips of the slide to remove top rack. You simply need to squeeze the plastic clip in to slide it out. Once the top rack is out, it was an obvious philips head screw removal and new part replacement.

1-remove upper rack by removing holding clips.

2-remove old assembly from Rack

3-cut old ring guide to accomodate new style (one solid plastic piece) and reglue after accomodating new assembly

4-re-install upper rack

DONE

Removed one screw to get the spray arm off the rack, one other screw to disassembly the spray arm assembly. Replaced worn and damaged parts. Installation was reverse order of disassembly.

Removed the rest of the broken retainer plug. Part number was on the top of the plug. Went to Partselect.com looked up the part and ordered it. The right part (important) arrived in a few days. I put the arm back in place, screwed in the new retainer plug and we were back in business. Cost of part about $5.00. Price of not having to share in cleaning the dishes, priceless. Any future problems with any of my appliances, this is the first place I'll look for the needed part.

I removed the screws on the door cover and snapped in the new clip

for the arm I just removed one screw and replaced the arm

I was hesitant at buying the Matag made replacement, especially since it was one piece as compared to my 10-year old 3 piece assembly, and my dishwasher is KitchenAid.
Ordered on a Sunday afternoon, had in hand Tuesday same week, one phillips head screwdriver to remove/replace. Everyone smiling!
Did not need to remove upper rack. Simply unscrewed 1 screw, put on new one-piece arm, replaced with same screw.
15 minutes!
Good price/delivery.

Replaced the middle spray arm kit and the upper spray arm mount. Also replaced worn out spring for the soap dish.
Now all areas of the dishwasher get cleaned and the soap dispenses correctly every time.