6651580590 Kenmore Dishwasher - Instructions

I bought the kit because it had other parts that I thought I needed.

after that every thing went very well

Recently bought a whirlpool dishwasher, the dishwasher was converted to a portable dishwasher and they did not use the cord application power cord so they machine was blowing our breaker, instructions were very simple and installation was easy!

removed and installed cords with screw driver

The lower dish rack rolls directly out of the dishwasher without problem - there is no permanent attachment. The new rack comes as a kit, which includes the 4 required dish rack wheels (Part # 6 in the diagram). One part (only) from the original dish rack needs to be removed and re-installed on the new rack - the upper spray arm tower (Part #5 in the diagram). That is easily removed from the original rack with a 1/8 counterclockwise turn, to disengage the 'feet', and installed on the new rack with a 1/8 clockwise turn. The kit is designed to allow for use on multiple models, so there are 'extra' parts left over, after it is used for the DU8500XX-2 dishwasher. These can be discarded.

This job took 30 seconds to accomplish. The old wheel assemblies (4) just snapped off and the new wheel rollers just snapped in their place. No tools were needed. Extremely satisfied with this product. Wished I had performed this repair years ago!

Was a simple task to perform, a child could have done it. The technical skills diagnosing it was a bit hard though. The skills finding the culprit was indeed simple. Rubber was torn. Dishes would not come clean especially on the top & would not dry properly. The rubber piece being torn in half made it hard for the water & soap to despense to the top through thh center plastic tube, but now it cleans great. Thank's
Now to find out why it won't dry properly at the heating element is another task. It leaves water droplets on the dishes.
Once I got the rubber screw on attachment installed the dishes are clean & dry now & no water dropplets on the dishes.
The water dispenses up to the top like it suppost to throught the small tube to wash the upper rack dishes.
The wife is happy now she doesn't have to clean & dry them by hand.
Thank's so very much!!
Now on to the next project in hand to submit later on.

removed the 2 screws that hold in the washer, pulled it out, with the door shut, removed and replaced the remaining spring , then went to the other side and did the one that broke off. then I reinstalled the unit. simple !

The 1/4 inch impeller bolt to shaft would not budge with a nut driver so I had to use a ratchet to loosen it. I could not hold the drain impeller with an adjustable wrench so I had to use a vice-grip. This still did not loosen it so I used an oscillating power saw to cut away at the bottom of the drain impeller being careful to only cut so deep, I didn't want to cut into the motor shaft. Once I had cut some grooves into the drain impeller, I could break it into pieces and remove it. Upon reassembly I tightened the 1/4 inch bolt with the ratchet.

I simply snapped off the old broken roller set and snapped on the replacements. No tools were even needed and now the rack rolls smoothly on all wheels! This has encouraged me to try other
repair projects.

follow instructions, unscrew old part, screw in new part, worked like new

It was very easy to install the new parts successfully thanku parts select I will always keep using your business the representative was so helpful and understanding my problem I wish I could remember his name he was outstanding and a 100 thumbs up to him

Remove power source, then remove old power cord.Run new power cord through existing opening ang attach to existing power box on bottom o f dishwasher. Install electrical leads and device ground. Reinstall cabinet bottom. Check out operation by running a cycle. All ok!

Removed the two screws securing the dishwasher to the underside of countertop.
Pulled the washer out until the spring mechanism was visible. Vacuumed the area - it was filthy. Assembled the spring and adjusting hook. Took me 4 tries to get the spring into the proper tension slot. Having the other side intact helped in understanding how it worked. Used long nosed pliers to bring spring onto the door retaing plate slot after trying unsuccessfully with regular pliers.

Pulled out the DW and removed old spring parts. Used screw driver and pliers to respring