66515777990 Kenmore Dishwasher - Instructions

No brainer

The old gasket came out easily, but had calcium deposits in area. I cleaned the area with vinegar and water and waited until it was completely dry. The new gasket went in very easily and looked great. I started the dishwasher and alas, it still leaks, so the problem was apparently not with the gasket, but some other area. But the gasket is nice and new. Any suggestions on next step0 in troubleshooting?

1) Removed the two white clips from the left and righ hand side of the top tray roller rail. this allows the tray to be completely removed and ease access to the washer assembly. The clipe looks like the letter "k", so you will need to close the "k" to almost straight line in order to get it through the hole.

2) Put a sheet or a towel at the bottom of the machine, just incase you drop the two small cross head screws. This prevents the screws from falling to the bottom of the machine.

3) Remove the screws. At this time the washer assembly will/should slip out very easily. very little force is required to pull the assmbely out.

4) Slip on the new washer assembly and put the screws back in place. Tighten screws, Be careful not over tighten the screw as you may crack the plastic flange.

Note: My machine is an older model, so the washer assembly had two screw fixing. The new assembly only had one hole. Although one fixing appeared to be sufficient, I decided to drill a hole on the other side and this worked fine.

5) Replace the top tray, taking some care to ensure rollers are correctly located within the rails. Then replace the clips and job's complete.

Removed inner cover of door. Pried Vent Assembly from door, peeled off thin sponge gasket strip from inner door, installed new thin sponge gasket strip on inner door vent opening bottom, snapped Vent Assembly into inner door opening, reinstalled inner door cover to door.
Recommend removing Vent screen from inner door first to expose locking tabs of Vent Assembly to ease removal and installation of Vent Assembly. I assume vent cover will come off if pried with small screw driver. I didn't remove vent cover and had difficulty removing and installing Vent Assembly. (I did accomplish it though)

first i picked out the old seal, use a screwdriver to get it started. Then I pushed the new one in after cleaning the seal channel. I fixed it during a commercial while watching my favorite tv show.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Installed the new upper spray arm mount. First I installed it backwards which made the blades not turn freely (rub against top rack basket). Turned it around and was good to go. I found it helpful to remove the top basket in order to do this. Note that this clip is gray while your dishwasher tines are white. This does not cause any harm.

Plastic parts on this Kitchenaid dishwasher suffer repeat wear problems from heat and chemical detergents. The retainer nut on the bottom wash arm split horizontally int the thread area, and during operation, the wash arm would rise up and hit the bottom of the lower basket so there was a worn groove in the wing on top of the nut and the dishes weren't getting very clean. Simple replacement, just screw the nut down. Also decided to replace the bearing ring right under the wash arm because it was getting pasted with white crust-like material from hard water and chemical detergent residues. I've dealt with PartSelect twice now, and they are fast and efficient. The online parts breakdowns are easy to follow.

Bottom wash arm bearing and seal were severely worn and leaking. Replaced in about one minute with new parts from PartSelect.com, and took the opportunity to clean out the arm -- stringy, fibrous matter was clogging two jets.

Top arm horizontal rubber supply tube was disintegrating and leaked. Replace with Spray Arm Kit -- this took maybe two minutes!

Lastly, two to of the upper right-rear folding rack tine clips were broken -- replacement was difficult as the old, broken clips were very stiff and came off only after much physical persuasion! New clips were installed easitly -- in a "snap". Time ~ 5 minutes.

Best of all, the new parts were delivered to my home within 36 hours of my internet order. I thought the prices were fair, too. Thanks.

I first removed the old part. when i removed the old part i could not get the conector piece off when i when to get a new one they told me i should replace the copper tubing with the more flexable tubing because the copper tubing can kink up and possibly break from the kinking. so i screwed the inlet valve on i put teflon tape on the all the threads of the conector piece screwed it into the new inlet valve with and adjustable wrench then i conected the new tubing, and tightend it down with the wrench i slowly turned the water back on to cheak for leaks. When i saw there were no leaks i turned the water on the rest of the way pushed the dishwasher back in and screwed it into place an i was done.

Simply removed deflectors and gasket, replaced all , took all of 5 mins. workes great now.

unscrewed sprayarm, removed bearing and seal, used PartSelect pic and description schematic to identify part numbers then placed order. Parts arrived in two or three days.

Removed upper basket and installed the arm. New snap in didn't require phillips screwdriver as old one and new support had split to insert. Replacing upper spray spinner dropped screw down around pump. This caused misery unassembling lower covers to receive Stainless
Steel, so magnet won't help ended up with mirror and hemistat to reach through large screen figures. So make sure to put towel or something in the bottom to catch parts.

After pulling the dishwasher out from under the cabinet, I found it underneath near the back right side. I disconnected the old thermostat, unscrewed the clamp holding it into place, put the new thermostat in, screwed it back in and replaced the two plugs. Then I pushed the dishwasher back into place, and it initially didn't work until I found an online forum that was able to identify the reset command for my dishwasher (for the WDT710PAYM4, press any three buttons in a sequence of 1 2 3 1 2 3 1 2 3. After completing that all the lights lit up, and I shut the door leaving it for half an hour) Once the reset finished, the heated dry worked like it was suppose to.

first I removed lower basket. then removed lower sprayer attached to pump housing by unscrewing the cap by hand. the I removed the pump cover . there were six alan screw two of them were missing causing the failure of the seal spraying solution at the door. replaced the pumpseal working backwards until everthing was replaced.