All Installation Instructions for Kenmore Dishwasher 66513922K011

Dishwasher door had lost springback

1) Pull out dishwasher from under counter. 2) Disconnect spring located at the bottom on each side of dishwasher. 3) Using socket remove pulley wheels from each side at bottom. 4) Install new pulleys on each side. 5) Wind pulley cord around both wheels and attach to one end of the spring on each side. 6) Using pliers extend other spring end to lower frame of dishwasher on each side. 7) Open and close dishwasher door to test. 8) Replacement complete

Parts Used:

Door Balance Link Kit

Peter from BIRMINGHAM, MI
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Socket set

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Broken plastic piece in door balance link kit

Watch video and followed instructions. Very easy!

Parts Used:

Door Balance Link Kit

Pauline from FERGUS FALLS, MN
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Wrench (Adjustable)

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Broken cord on door balance

Very easy. I removed the two screws on the base plate, then the two screws that attach the washer to the cabinet, and pulled the washer out of its slot. I installed the broken side and closely checked the other side and felt it didn't need repairing. I put it back together and the door works very well.

Thanks,
Ted K.

Parts Used:

Door Balance Link Kit

Ted from Santa Clarita, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Socket set

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

The Door Leveler Nylon Cord assy broke

It was very easy.

Parts Used:

Door Balance Link Kit

Robert from Highland Village, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

If I can do it, you can do it.

Replacing the rear wheel assembly isn't as easy as replacing the front, which took 5 minutes. You have to align the tine row, so it takes a few minutes more. But I'm a tiny woman with long nails, and if I can do it, you can do it!

Just watch the video, follow the directions, and you can't go wrong.

Parts Used:

Lower Dishrack Wheel Assembly

Ellen from GREENWICH, CT
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Lower Dishrack Wheel Replacement

Simply take out the lower dishwasher rack, grab a pair of pliers and gently pry the old assembly off and snap the new assembly into place. It's very easy.

Parts Used:

Lower Dishrack Wheel Assembly

Jeff from LAS VEGAS, NV
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Upper drawer rack stop clip broke caused one side fell off rail.

I followed the YouTube attached with PartSelect email invoice to fix it. I am very happy PartSelect sent repairing video instruction and took me less than 15 minutes to get it done. Awesome!

Parts Used:

Rack Stop Clip

Pooi from TORRANCE, CA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

none

removed and installed cords with screw driver

Parts Used:

Power Cord Kit

Ronald from VAN BUREN TWP, MI
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Plastic stop on front of drawer track broke off

1. Remove the top rack
2. Take a screwdriver and pry off back plastic stop at end of track
3. Slide track off, then slide new track on
4. Take the plastic back stop originally pried off of old track and snap into new track
5. Open plastic stop at front of track
6. Replace top rack.
7. Close plastic stop at from of track
8. Good to go!

Parts Used:

Dishwasher Drawer Track

LES from NORTH PORT, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

The rollers wear out. This is the third set since it was new.

I removed the upper rack and unclipped the roller assembly and snapped the new ones in place.

Parts Used:

Dishwasher Upper Rack Roller

gerard from CAMARILLO, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Door of the dishwaher banged open

Pulled the dishwasher out and took the two door balance links off and put the new ones on and attached to the spring. It was very quick and easy

Parts Used:

Door Balance Link Kit

edward from sullivan, OH
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

The Inlet Valve cracked from the severe cold weather we had in Chicago area.

Removing and installing the new part was fairly simple. We removed the water hose first since it is the easiest to see. We then removed the screw holding the part to the metal frame. We slid out the part out of the holder to remove the black hose and electric plug (it is like the old phone jacks). After it was completely off we plugged in the electric to the new part which was very easy since it can only go in one way. We slid the new part in place and attached the black hose. We attached the piece to the frame with the one screw and last we attached the gold (garden hose) connection. We turned on the water to look for any leaks then turned the power on and ran it through a partial rinse to be sure there were no leaks.

Parts Used: