66513273K114 Kenmore Dishwasher - Instructions

I simply removed the melted spray arm, then set the new spray arm in place, twisted the built-in securing nut (clockwise to its stop), and it worked without any problems.

took out the top dishwasher rack. Pulled out the track needing repair. used a flat screwdriver to pry off the defective stop. Slid the track (without the stop) back over the rollers. Snapped in the new track stop and that was it.

First I identified the problem by checking the plug ends of the heater coil with an ohm meter. I quickly odered the part and when it arrived a few days later, I simply pulled off the electrical connectors, unscrewed the two bolts, removed the old/broken coil, put in the new coil and tightened down the nuts snuggly.
Nothing to it. I then had to reset the error code and it is working like new.

You only need to pull it out about 6 to 8 inches and you don’t need to disconnect anything to slide it on

Removed the old hose, after loosing metal looking rings. Installed new hose ad finally tight firmly the looking rings, using wrench and socket.

Looked on you-tube and it was so easy. Pump on bottom right. unplug pump and do a halfway turn. Plug the new one up and place the pump on, and turn halfway and its on. START your dishwasher

thought it could be due to the overfill control switch,so ordered one and replaced one in the washer. However, it did not solve the problem. Having a repair company coming to look at the dishwasher. Tipped the washer on its back and switch was readily accessable. Only had to open plastic covering over the switch, disconnect the wires and install new switch and reconnect the wires.

I simply had to hook up the power cord to the dishwasher so i could plug it into the outlet rather than direct wire the appliance. Everything went very smoothly. Everything needed for installation other than tools was provided. Easy to follow instructions if you know a little about electrical wiring.

Did the repair, but needed one extra step not described in video:

I followed the directions on the PartSelect Youtube video - very helpful! I do believe the heating element was the original culprit, as it had a "burn" area about the size of a dime that caused it to almost break into two parts. Obviously a point of failure.

BUT - after replacement, it still did not solve the problem of the dishes not drying.

After much web searching, I tried the diagnostic mode on the dishwasher, and that did a hard reset of the logic board and FIXED the problem.

So in all, it required both a new heating element AND a hard reset via diagnostic mode.

Followed the easy how-to video from PS. It was as easy as changing a light bulb.

Actually, I found a video on Youtube with excellent instructions once you got past the really simple stuff like disconnecting power and water and drain.
I would recommend just finding a fairly similar model on Youtube and follow their directions. It was really easy.

The repair was similar to the very good video provided by PartSelect. However, I did make a few changes. The new rack was slightly different in the front side compared to the old rusted rack. After I removed the old rack from the dishwasher, I placed the two racks side-by -side to make sure they were compatible. They were identical in the rear structure and overall size, so I proceeded to change out the wheel racks, rack height adjusters and upper wash arm to the new rack. I suggest transferring each part one at a time so you can get the spacing correct. Also, in my case, many of the items needed to be washed with water to remove soap buildup in these parts before moving to the new rack. I would also suggest putting the upper wash arm (needed in this case) on the new rack last. The total job took me about an hour including washing or rinsing all parts and reassembly. This is an easy job, just take your time and do one item at a time so nothing gets mixed up. I used a drill driver to remove a total of 4 Phillip head screws for the rack height adjusters but a regular Phillip head screw driver would work as well.

12 screws remove door outside panel unplug wire remove 6 mounting screw remove old unit put new unit in place put 6 small mounting screws back plug wire in put front door panel in place put 12 door screws in your done now you can start and test run

First I got online to troubleshoot issue to save mysel from a service call. One of the first UTube videos, a young man said usually the main issue was the lever. He pushed down on the floater. If it didn't click, than the lever below needed to be replaced. Most important to turn off the circuit breaker before beginning the repair. I got on whirlpool.com, Part Select, ordered the lever, which was under $10. And once delivered, was able to switch out the old lever with the new replacement. Part Quote video took me through the process step by step. The lever package was marked that usually it was only 2% of the time that replacing the lever fixed the issue. Of course, I was thrilled, my dishwasher was up and running again. Thank you.

Follow the u tube instruction. Replacing the pump was very simple and easy. The hard part was getting the dishwasher out of the cabinet and back in again.