65715755791 Kenmore Dishwasher - Instructions

Installed new door seal. Dishwasher still leaked. Googled the model number and then cleaned the filter at the bottom of the dishwasher, still leaked.
Verified that manifold bearing was not work. It was OK.
Found note that a plugged vent might cause leaking door. Very counterintuitive. Pried off air vent cover. Vent was thouroughly plugged with calcium deposts from steam. Cleaned these out.
Dishwasher no longer leaks.

Ordered both drain & wash impeller kit and the drain check valve with o-ring. Decided to test the cheaper drain check valve first. Pulled dishwasher out from wall & adjacent cabinetry; removed drain hose from disposer and drained as much water as possible; "jacked" side of dishwasher to gain access to drain hose and drain check valve; used pliers to remove hose clamp; placed flat pan underneath to catch remaining water drainage; unscrewed drain check valve; tested under bathroom faucet--determined faulty; replaced with the new one, restored connections, reset dishwasher in proper location; voila--fixed! Plan to return the unneeded impeller kit.

The first thing I did was to investigate. I needed to find where the leak was coming from. It was leaking from just above tne door front panel, directly underneath the control panel buttons. I opened the dishwasher door, and decided to remove the door screen vent. I was covered with some offwhite fiberous, or filter like material. I thought perhaps the filter had broken down, and I ordered a new screen. When it arrived, and, although I had expected to receive a new filter with the plastic door screen, I didn't. There wasn't one to be ordered. I looked at the screen again. My problem was, that although I had considered that the substance I had thought was a filter, was instead build up of detergent, and other particals. That idea didn't seem to make sense. I didn't think it was possible for that stuff to get to the door screen. I thought, it was too far away from the dispenser and food particles. As it turned out, the buildup was, in fact, the problem. I properly cleaned the door vent, which was then fine, and I put it back into the door. There were no more leaks, that was it, and the problem was solved. As a last note however, unfortunatley, I have to return the new door vent screen that I ordered. I enjoyed solving the problem, and you all helped alot. Let's do it again sometime.

I removed the old gasket, installed the new one which took about 20 seconds.Tested the unit, water was still dripping, but in a different fashion.As per a previous poster's instructions I removed the vent cover. (Located inside the dishwasher up high.)I cleaned out the calcium deposits with hot water and a sacraficial toothbrush. "Ta-Da!" Everything is now groovy!Thank you so very much for your excellent service. Your site was easy to use and your shipping was "lightning fast!" Also, the advice you sent me was invaluable. I thank you, my wife thanks you and my trained lobster thanks you too! :)

First, examine very carefully how the old spring relates to the detergent release box lid. Note that the top of the spring has a square-end upside down "U" . This rests on a small ledge on the detergent box. Also note that on either end of the spring is a straight extension of the spring wire. These two "legs" must rest on the inside of the edge of the detergent box. Second, use a flat blade screw driver to pry the LID hinge pin from the mounting "posts. Remove the pin, first noting the position of the spring. Reassemble the spring on the hinge pin in reverse order. Then snap the lid onto the spring using the two mounting "posts". NOTE: I used a very fine needle nose pliers to move the two spring "legs" behind the detergent box edge after I had mounted the lid. Flip the lid down to test if the spring pressure on the lid can be felt. Harold Kitzmann, Fishersville VA

This repair was very simple. I opened the door of the dishwasher then pulled the old rubber seal (gasket) out; I checked the old gasket to with the new one to ensure the new one was correct then installed the new one. There are two small rubber pieces located in mounting slots below the door gasket that slide out; I slide the old ones out and slide the new ones in. No tools required.
The thing that made the whole job easier was ordering the parts from Parts Select; I couldn't find exactly what I needed on the Whirlpool website but I found exactly what I needed on the Parts Select website and the parts were a perfect match.

The only piece that may be a little difficult to remove here without a tool is the 'Track Stop'. This piece has a couple of clip-like pieces that need to be depressed in order to remove it. A flathead screw driver will do the trick. Once this piece is out and you have popped the Mount off of the Rack, you simply roll the piece out of the track, roll the new one in and snap the new Mount in place, replacing the Track Stop when you are done. VERY EASY!

Removed the lower panels from beneath the dishwasher door. 4 screws. Turned off the water.

Removed one screw holding the inlet valve to the side rail of the dishwasher. It was attached to the hot water line and then the washer water input line. Removed the electrical connector..Pull straight off, and use a pair of pliers to open the squeeze clamp on the washer hose. The hot water supply hose has a brass fitting to loosen and remove.

Replaced the inlet valve, reconnected the electrical and also replaced the hot water line from under the sink to the washer. Used a new braided 5' hose with fittings. Used teflon tape on the screws and did not over tighten the brass fittings.

Turned on the hot water supply and checked for leaks. Operated the washer and checked for leaks. Replaced the lower covers.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

I thought that the valve inlet was defective. Ordered the replacement, got it in one day, replaced the part...
and it worked perfectly. Saved big $$ in a service call. Found everything I needed online.

I shut off the power to the dishwasher, then I removed the front panel under the door. On the right side just behind the electrical box there are two wires going up to the hi-limit thermostat, (you may need a small mirror to see it), remove one screw that is holding the thermostat bracket, unplug the wires from the old thermostat and install new one. Screw bracket and thermostat back to the underside of the dishwasher, reinstall the front panel, turn on the power, done.

I inspected the pump and checked on-line for instructions . I removed the lower panel and the lower dish rack . Removed the washer head from the top of the pump inside the dishwasher . I next unplugged the wiring after disconnectiong the power supply . Next step was to remove the drain hose from the bottom of the pump . Put a towel under it because it's full of water . Unscrew the nipple from the bottom of the pump to allow clearance so it may be removed thru the top . There are four plastic ears that rotate on the base of the pump . Move them into the outboard position and lift the pump out thru the top. I applied some liquid detergent where the pump seal goes and pushed it back in . Installation is the reverse of removal .

Look at the exploded parts diagram, that parts select provides on their website.

You have to take off the nine star pointed screws. So you need a special screwdriver or I had a socket set of them and I used a ratchet to make it easier. I think there are nine of them around the base of the door. Then remove the door and set it on the counter. Flip it over and there is a small plastic cover that has to be removed from the back of it, and it is easily removed by gently pulling on it.

Now comes the difficult part. There is a locking piece on it that holds the latch onto the door by interlocking with a piece on the back side of the door. I took a pair of wire snips and just cut the old interlocking piece off. This way I didn't have to try and slide the two interlocking pieces apart.

When you go to put the new piece on before you interlock them make sure they are put on right. Specifically the latch is pointing the right way to seal the detergent door. Otherwise it can be a pain to separate the interlocking pieces again. (which is why I cut it off the old one).

Then you're done. Just put it all back together.

Removed dishwasher lower faceplate.
Removed hose clamp at the dishwasher end.
Removed clamp at the garbage-disposal end.
Removed hose.
Pulled new hose.
Connected both ends of the hose.
Installed both clamps.
Tested.

Disconnect power supply to dishwasher. Open door and remove screws on inner door cover. Carefully remove inner cover while watching how inner parts are arranged. Found return spring on detergent cup linkage had rusted and broken causing detergent cup not to open. Installed new spring and re assembled inner cover. Rotated timer dial one full revolution to check operation of detergent cup. Worked like a charm. Re connect power supply to dishwasher and your good to go.