Models > 6440A REV A

6440A REV A Norge Washer - Overview

Sections of the 6440A REV A

[Viewing 1 of 1]
Keep searches simple, eg. "belt" or "pump".

Questions And Answers for 6440A REV A

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Common Symptoms of the 6440A REV A

[Viewing 14 of 14]
Noisy
Fixed by
these parts
Show All
Shakes and moves
Fixed by
these parts
Show All
Leaking
Fixed by
these parts
Show All
Burning smell
Fixed by
these parts
Show All
Pumps but will not spin
Fixed by
these parts
Show All
Will not drain
Fixed by
these parts
Show All
Lid or door will not open
Fixed by
these parts
Show All
Spins slowly
Fixed by
these parts
Show All
Lid or door won’t close
Fixed by
these parts
Show All
Will not agitate
Fixed by
these parts
Show All
Will not stop filling with water
Fixed by
these parts
Show All
Will Not Start
Fixed by
these parts
Show All
No hot or cold water
Fixed by
these parts
Show All
Timer will not advance
Fixed by
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
washing machine was making alot of noise
I found the water pump bearings were going bad from humidity. I replaced the pump with a new one and it runs quiet again.
Parts Used:
Drain Pump with Pulley
  • David from Boca Raton, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers, Wrench set
554 of 562 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
One of the plastic hinge pins brroke
I used a flat screw driver to push in on the releases so I could raise the top of the machine. I then used a torx tool to remove both parts of the hinge, and then used a #2 phillips screw driver, on the new screws I'd also ordered, to re-attach both of the hinge parts. Every thing went just as anticipated.
Parts Used:
Lid Hinge Pin Lid Hinge Screw
  • Allen from North Little Rock, AR
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
510 of 513 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Load Grinding/Rubbing Noise in Rinse and Spin Cycles
First unplug the washer for the electrical outlet. You will need to tip the washer back to get to the bottom of the machine. There you will see the belt that drives the transmission and the water pump from the motor. Remove the belt and set it to the side. Then you will need to gain access to the top side of the machine by gently using a screwdriver to pry the front of the top up off the front panel on both sides then hinge it back out of the way. Use a nut driver to remove the two screws on the inside edge of the front panel and remove the front panel. Once the front panel is off you will see the water pump on the right hand side as you face the front of the machine. Remove the hose clamp on the water pump with the flat head screw driver or nut driver and use a pair of pliers to remove the compression clip on the water pump. Remove the 4 bolts holding the water pump in place. Reverse the entire process to put it back together. This job was very easy and I was only without a washer for 2 days because of partselect.com.
Parts Used:
Drain Pump with Pulley
  • Doug from Port Richey, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
139 of 151 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!