6432A REV B Norge Washer - Overview

Diagrams for 6432A REV B

See every part. Know exactly what you need.

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Drive Belt - 51 inches long – Part Number: WP21352320
$24.17
In Stock
Drive Belt - 51 inches long
★★★★★
★★★★★
(16)
Part #WP21352320
This V-style drive belt is about 51" long and 3/8" wide. This part is made to slip on the motor pulley to bring the basket up to the speed required and this makes the belt encounter wear and tear.
Snubber Ring – Part Number: WP21002026
$18.31
In Stock
Transmission Pulley and Bearing Kit – Part Number: 12002213
$73.65
In Stock
Transmission Pulley and Bearing Kit
★★★★★
★★★★★
(21)
Part #12002213
Also known as Thrust Bearing Kit. This kit includes the pulley, washer, thrust bearing, 2 upper race washers and 1 lower race washer. These parts are NOT available separately - they are ONLY available in this kit. A worn bearing causes slow or no spin.
Drain Pump with Pulley – Part Number: WP35-6465
$159.64
In Stock
Drain Pump with Pulley
★★★★★
★★★★★
(24)
Part #WP35-6465
This pump has 2 ports. This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time.
Washer Hose Clamp – Part Number: WP596669
$11.52
In Stock
Washer Hose Clamp
Part #WP596669
This hose clamp extends from half an inch to an inch in diameter. It is made entirely of metal and is intended for use with Maytag brand washing machines.
Screw – Part Number: WP489483
$17.55
In Stock
Screw
Part #WP489483
This screw is sold individually.
Dryer Screw – Part Number: WP90767
$10.40
In Stock
Dryer Screw
Part #WP90767
This screw is sold individually.
Screw – Part Number: WP25-7893
$11.80
In Stock
Screw
Part #WP25-7893
This screw is less than an inch long. It is a metallic screw that is used for many clothes washers. Sold individually.
Inlet Hose - 5 FT – Part Number: WP89503
$27.55
In Stock
Inlet Hose - 5 FT
★★★★★
★★★★★
(3)
Part #WP89503
This hose can handle hot or cold water and is five feet long.
Range Screw – Part Number: WP3196164
$13.89
In Stock
Range Screw
Part #WP3196164
This screw is sold individually.
Lid Switch Actuator - Black – Part Number: WP43-0057
$73.01
In Stock
Lid Switch Actuator - Black
★★★★★
★★★★★
(1)
Part #WP43-0057
This is part of the lid switch actuator mechanism and activates the lid switch, when the lid is closed, to start the wash cycle and when the lid is open, it stops the cycle.
Transmission Lower Lip Seal Repair Kit – Part Number: 207843
$26.35
Special Order
Transmission Lower Lip Seal Repair Kit
Part #207843
This transmission lip seal repair kit comes in two pieces: a red four inch long piece, and a black one inch long piece. Both pieces are made entirely of plastic. This repair kit comes with and instructions sheet and it is used for some washing machines.

Common Symptoms of the 6432A REV B

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
washing machine was making alot of noise
565 of 581 people found this instruction helpful.
  • David from Boca Raton, FL
  • Easy
  • Less than 15 mins
  • Screw drivers, Wrench set
I found the water pump bearings were going bad from humidity. I replaced the pump with a new one and it runs quiet again.
Was this helpful?
Thank you for voting!
Load Grinding/Rubbing Noise in Rinse and Spin Cycles
139 of 155 people found this instruction helpful.
  • Doug from Port Richey, FL
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
First unplug the washer for the electrical outlet. You will need to tip the washer back to get to the bottom of the machine. There you will see the belt that drives the transmission and the water pump from the motor. Remove the belt and set it to the side. Then you will need to gain access to the top side of the machine by gently using a screwdriver to pry the front of the top up off the front panel on both sides then hinge it back out of the way. Use a nut driver to remove the two screws on the inside edge of the front panel and remove the front panel. Once the front panel is off you will see the water pump on the right hand side as you face the front of the machine. Remove the hose clamp on the water pump with the flat head screw driver or nut driver and use a pair of pliers to remove the compression clip on the water pump. Remove the 4 bolts holding the water pump in place. Reverse the entire process to put it back together. This job was very easy and I was only without a washer for 2 days because of partselect.com.
Was this helpful?
Thank you for voting!
washer would agitate, pump, but not spin
62 of 74 people found this instruction helpful.
  • steve from lebanon, OH
  • A Bit Difficult
  • More than 2 hours
  • Pliers, Screw drivers, Socket set, Wrench set
First I unplugged it, then removed the agitator and tub assemblies, then I tipped it back and removed the belt and pully and thrust bearings. After reading on here I learned the brake would stick and after installing the thrust bearing kit I found out I couldnt fit in the shims. That led me to believe the brake was siezed inplace so i cou ldn't fit in the parts. I removed the thrust bearing kit and removed the transmission assembley. I took apart the brake and found the two pieces had siezed together, after I got them apart I sanded both peices and lubed the shaft with high temp silicone like you would use on a cars brake system. I put the brake back together, BE VERY CAREFUL THE SPRING HAS ALOT OF PRESSURE! I then put the transmission back in, reinstalled the thrust bearing kit and it fit great. I put in the tub and agitator and washed clothes.
Was this helpful?
Thank you for voting!