63198419 General Electric Dryer - Instructions

I first removed four screws above the door opening to lift off the top, then removed two screws, near the top, inside the front, to remove the front. There I found that 2 grey plastic and one white plastic anti-friction strips were worn to nothing (even the large plastic bezel that incorporates the light was starting to wear away, from just a few days!).

When I went to put the front back on, i couldn't get the lip of the drum to ride properly on the felt. In fiddling with it, the drum fell off the rear bearing, too, so I put it back on.

So I ordered new felt, two white and two grey strips (I didn't know if 1 or 2 were in each $8 "kit"--only one per kit), a spare belt--just in case--and some bulbs.

Putting the strips on was easy--15 seconds each. Putting on the felt took all of 20 seconds. I spent more time scraping off the dust and vacuuming things out!

The drum fit over the felt quite easily now, and when I ran it, it was wonderfully quiet. For a minute! Then, it started making a new, grinding noise!

I had a Sears repairman friend come over, and he found that a small platic bushing had fallen off the rear bearing element. Once he put that in place, it all worked perfectly. Beautifully quiet!

Unscrewed screws took off new parts and replaced with new parts and put back together. Works great now! No Noise!

I followed the directions from the previous post. It was much easier than described. I got the part, removed 4 screws, removed the top, pulled the front and replaced the part. It was all together again in 15 minutes. Dryer sounds great again! I'm so glad I didn't call a repair man!

remove move 2 screws holding top of dryer down.then remove two top screw holding front panel on so i could get to were my slide bearing where at poped them out and slide in new ones then put it all back together that was it

todd e line eaton ohio usa

i first popped off the top of te dryer after removing the two screws in frotn when you open the door. I then removed the two screws holding the front together. after tilting the front out i was able to place the slides in without having to pull of the front entirely.

it was easy, it clip right on.needed to give it a little tap to get it in .

First I removed the 2 screws that hold the lid down. Then I pulled the lid off. Then I removed the 2 screws that hold the front of the dryer in place. Then I lifted the drum a little and pulled the front cabinet out a little so I could see the drum slides. I removed the bad drum slides and installed the new ones. I then put everything back together and turned on the dryer. The squeeky noise was gone.

I took out a whooping four (4) screws, two that held down the top to the front panel then two screws that attached the side panels (at the top) to the front panel, raised the drum from the inside, leaned the front panel foreword, popped out the old slide (there was only one left), installed the four new slides & put it back together. That's pretty much all there was to it, vary simple.

Took the top of the dryer off by removing two philips screws in front. Removed two screws holding the front of the dryer on. Pulled the front out enough to reveal the worn drum slides. Replaced them. Reassembled.

Looked up the problem and solution on the web and,ah-ha, drum slides should be the cure. Easy to install, . Back to the internet to discover that after the slides, the bearing and felt liner were the next likely culprits. Again easy install, but to no avail. Calling in the pros.

I took off the dryer top and saw it was the slides went on line found PartsSelect, found my dryer, ordered the parts and had them within two days and it took me about 15 minutes to fix the dryer which will add about 3-4 years more life on it. Thank You PartsSelect My wife is even happier

First I removed the drum as described in many other comments. Took me about 10 minutes, pretty easy. Replaced the part which was easy and could be figured out just by seeing how you took the original part off. The hard part was aligning the drum, drum washer, and metal plate back into the drum bearing. I tried over 2 hours to do this and because it rotates and it's almost impossible to line up all the holes, I decided to do it another way.

I took apart the drum bearing from the back panel and then outside of the dryer walls I aligned the drum, washer, metal plate and drum bearing. I screwed them all in together and then, went into the frame and reconnected it at the back w/ the horseshoe looking washer. It worked perfectly and I was frustrated that it took me so long to figure out a different way to do it.

I have to say because of the installation it was a little tough than anticipated but was very happy with the end result (no squeaking) and money savings. Definitely worth giving it a try if you're patient.

I ordered and replaced the front and rear bearings, including the slides that go on the front bearing. Most of this was un-necessary; replacing the slides would have been sufficient, and much easier to do. Two of the old slides were worn completely away.

Actually, my boyfriend did the repair by taking off the top and back of the dryer to access the drum and belt he replaced the belt and put the dryer back together
We are greatful for your service and really happy we didn't have to drive all over to find the part.

Started with removal of rear inspection plate on rear of drier,rotated drier drum by hand to look for any visible problems. Found that drive belt with age had lost sections of teeth and every time the bad sections would go past motor they would "thump".
1. Removed belt from tensioner. Done simply by moving tensioner to unload belt.
2. Slipped belt off motor drive and moved belt to front of drum.
3. Opened drier door and removed 4 screws from under the lid or top of drier ,raised lid for access to belt once belt had been slid to front of drum.
4. (steps 4 and 5 are the hardest parts)Worked drive belt between drum and felt insulators keep in mind there are many stamped steel pieces and sharp edges can be present.
5. Removed belt by feeding a small section past felt and drum and worked rest out from frt. top of drier.
6. Installed new belt in reverse order as removal.
This was done without aid of instruction manual and by someone having major back surgery 4 months earlier. No idea how much this saved me but the price of the belt and time and effort involved made it woth my while I'm sure.