62170419 General Electric Dryer - Instructions

unscrewed and lifted top of dryer put belt around drum closed top put belt around motor pulley and belt tensioner and finished.( remember to unplug unit before working on it.)

There is a plastic female closure part in the dryer door that wouldn't close tightly around the metal male closure on the dryer. I popped out the plastic square with a screwdriver, popped the new plastic closure in with my thumb. Works great. I never even installed the new metal portion of the latch.

Watched the video on YouTube and everything went great!

I didn't know what was wrong at first, only that the dryer would not start. I bought it used so had no fear of taking it apart to diagnose. Found the broken belt inside, ordered a replacement, installed the new belt, then crossed my fingers. Was pleasantly surprised that was all that was wrong and that for less than $20, including shipping, a few hours of my time, and a little help from YouTube videos the dryer is working again!

sort of followed instructions, would have beenhelpfull if they told me I HAD TO REACH INTO THE MOUTH OF A SABRE TOOTHED TIGER to install the new belt.

After having a friend who repairs appliances come and diagnose the problem, I was able to find the parts I needed very easily at PartSelect. They came quickly and I removed the front panel, followed the instructions (they were not very detailed) and also had help reading some of the other posts from people on the website. I replaced the parts and the dryer is now quiet and running fine.

I did not have an actual repair. I simply replaced the lint filter that dropped into the receptacle. However, what I want to mention is that the part was available as old as the dryer is and there was a nice photo to scale of the replacement part so that I was sure I was getting the correct piece. A great site to obtain parts from my experience.

Just replaced it with the new one

The ordering and receiving of the part were wonderfully easy, but the construction of the lint filter left a lot to be desired. Bits of wire extended past the edge of the frame and drew blood when held, so had to trim the wire screen that extended past the frame. Also, the wire screen was not attached continuously around the frame and had to be clamped and glued. I did appreciate that the filter fit my machine.

The job is simple once you know how to remove the front panel. The steps are as follows:
1. disconnect the power cord.
2. remove 4 Phillips-head screws under the lip of the front panel that secure it to the top panel (#1 point Phillips-head screw driver)
3. swing the top panel up, it is hinged in the rear.
4. making note of the connection points of the color-coded wires, disconnect the wires to the lamp socket and door switch (I used a felt-tipped pen on the inside of the front panel to mark the connection points, "R" for red, etc.)
5. remove the upper 2 hex-head screws from inside of the front panel (5/16" nut-driver)
6. loosen the lower 2 hex-head screws (5/16" nut-driver) accessible from outside the panel (you only have to loosen them since the bottom mounting tabs are slotted)
7. slightly lift (to clear above mentioned lower tabs) and tilt the front panel toward you. Swing the front panel to the right as though you were opening a door and position so it does not fall.
8. remove 10 hex-head screws from the black lower rear access panel (5/16" nut-driver) and remove the broken drive belt. Note that the narrow black panel securing the power cable can remain in place.
9. at this point take advantage of the situation and vacuum out the years of lint and dust you could not reach before.
10. stand in front of the dryer, lift the dryer drum slightly and slip the new belt (rib side down) around the drum. Position the belt near the rear of the drum along the wear-mark left by the old belt.
11. go to the back and place the belt in the motor's drive-belt pulley, making sure the ribbed side of the belt mates with the ribs in the pulley.
12. position the tension wheel so that the it takes up the slack in the drive belt. Note the flat side of the drive belt will mate with the flat of the tension wheel.
13. spin the dryer drum a few turns by hand to make sure the drive belt lines up properly with the pulley.
14. reassemble the dryer by reversing the above steps, starting at step 8.

It wasn't so bad taking it apart, but getting the drum back on was a problem. So what i did was too turn the dryer over and cut the heads off of three long screws and slid the drum over top of these and it lined up with the bearing housing.After a few tries it finally lined up and then i put the regular screws back in to hold the drum in place, one at a time.

The same procedures as posted in the video, but as applied to the model. Belt had broken. Bearing and front supports were worn, but the cause of the noise was a worn tensioner pulley bearing/arm, causing damage to the belt until breakage. Save the time and effort of a second repair and purchase a tensioner arm/pulley anytime the belt breaks as this is likely the cause of the original breakage. The hardest part on this older GE was getting under the drum to engage the tensioner and belt to the motor, as clearances we very tight. Review the diagrams, watch the video, and enjoy a quiet and well running machine for your efforts. PartsSelect is the only place to shop for appliance parts, my hat's off to excellent service, fair pricing and fast shipment. Thanks PartSelect!

I unplugged the dryer and moved it into a open spot on the floor.I then opened the door so I could release the top panel,and tilted it back.This allows the removal of the front of the unit. Folled the instuction for removing the drum and got it out. Cleaned up the area and removed the screws that held the drum to the bearing, and pulled the drum out. The instructions for removing the plate and the bearing where o.k., and the tips given for reassembly were helpful, but would have been easier to see if the were a seperate line. The parts fit GREAT, and this 1989 dryer is ready for a few more years.A good price on the parts and a quick ship.I will shop here again!

I only ordered a lint filter with frame but wanted to let other's know that ordering from your site was extremely easy and the shipping was extremely fast!! I received my order with 2 days of placing my order. Thank you!!

inserted the latch into the opening in the front face of the dryer