5KSM70SKXZER0 KitchenAid Mixer - Overview
Sections of the 5KSM70SKXZER0
[Viewing 3 of 3]
Keep searches simple, eg. "belt" or "pump".
Bowl Arm Lift
PartSelect #: PS11746961
Manufacturer #: WP9706885
This is a replacement bowl arm lift for your stand mixer. It raises and lowers the mixing arm in the bowl. It is made of white plastic and is sold individually. This part can also be known as the bowl...
$13.15
In Stock
Order within the next 4 hrs and your part ships today!
Range Torx Screw
PartSelect #: PS11741257
Manufacturer #: WP3368921
7-18 x 3/4-Inch - sold individually.
$8.82
In Stock
Order within the next 4 hrs and your part ships today!
Flat Metal Beater
PartSelect #: PS16875729
Manufacturer #: W11646967
This Flat Beater is used as a mixing attachment for all six quart mixers and some five quart mixers. The Flat Beater is made from metal and has a burnished finish. This part attaches to the mixer on t...
$62.23
In Stock
Order within the next 4 hrs and your part ships today!
Mixer Pingroove
PartSelect #: PS11750745
Manufacturer #: WPW10234531
This groove pin is a small but essential metal piece used in stand mixers to secure the internal gears and keep the planetary assembly firmly attached to the drive shaft. When this pin wears out or br...
$12.47
In Stock
Order within the next 4 hrs and your part ships today!
Mixer Foot
PartSelect #: PS11746998
Manufacturer #: WP9708649
Sold individually.
$12.53
In Stock
Order within the next 4 hrs and your part ships today!
Dough Hook
PartSelect #: PS16875730
Manufacturer #: W11646968
$57.20
In Stock
Order within the next 4 hrs and your part ships today!
Screw
PartSelect #: PS11741603
Manufacturer #: WP3400814
Sold individually.
$11.94
In Stock
Order within the next 4 hrs and your part ships today!
Mixer Bowl Retaining Pin
PartSelect #: PS11740496
Manufacturer #: WP240185
Used for Kitchenaid Stand Mixers.
$11.95
On Order
Mixer Whipwire
PartSelect #: PS11756675
Manufacturer #: WPW10600940
Looking to improve your stand mixer's performance? The Whirlpool Wire Whip is here for you. This is a genuine Whirlpool part, designed to fit seamlessly with a variety of Whirlpool stand mixer models....
$101.15
Special Order
Clip
PartSelect #: PS11755746
Manufacturer #: WPW10504114
$11.95
In Stock
Order within the next 4 hrs and your part ships today!
Mixer Spring
PartSelect #: PS354210
Manufacturer #: 4159622
$11.35
In Stock
Order within the next 4 hrs and your part ships today!
Questions And Answers for 5KSM70SKXZER0
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the 5KSM70SKXZER0
[Viewing 2 of 2]Gas igniter glows, but will not light
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The mixer would not raise the bowl
I removed the motor assembly from the mixer. This left the stand assembly. The raising lift arm had to be removed by unscrewing the set screw, and then the lift arm was removed. I replaced the plastic arm bowl lift by sliding it over the lift arm, and then I had to remove the spring with a clip washer with the pliers, and replaced the spring back on to the new part. Total time about ten minutes for the actual fix, and about 45 minutes remove and reinstall the 12 screws that held the motor in place. It was well worth my efforts. The mixer arm works perfectly now.
Parts Used:
-
Stephen from Charlotte, NC
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers
12 of 19 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
all four feet on mixer damaged
I first ahd to remove the original feet by removing screws that held them in place. The new feet that I purchased were different then the original. They were a push in type and not held in by screws. I had to modify the base by drilling the foot holder to accept the new style feet. Once this was done, the feet were installed and looked good.
Parts Used:
-
ROBERT from ENDWELL, NY
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
5 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dough mixer paddle not turning.
-
Iftikhar from PACIFICA, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
3 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!