59679542014 Kenmore Refrigerator - Instructions

i had used your web site before and i read several problems that your readers had. i went to the back of the unit, removed the bottom cover and right there the i found the run capacitor and i chaged it. since i had only ordered this part to save money i went back and ordered the Start Device which when i took it off it was completely burned. the replacement part came labeled with 2 different compressor #, so i picked the one that i had and unpluged each wire. the part may differ from the one that it's in the unit but it worked when i pluged everything back on. it also helps to take a picture of everything before removing the wires in case you have to leave it and come back later. i hope to use this refrigerator another 10 years. thank you all for your help.

These guys had my part mailed in lighting fast! It arrived in 2 days in a padded box in perfect shape.The price was the best on line and they saved my life one day before thansgiving!! They got my vote and respect! Great job partselect!!! walt , crete illinois

I called the installer of my filter unit and he told me that often, thhe fridge filter is the problem. Like magic it worked

replaced the poorly designed "duck bill" drain with this P trap. Very simple repair done by accessing through the back of the refrigerator. The video on this website walked me right through the repair. It did however fail to mention that the ice has to be removed from the inside. I had to remove the drawer face and pull outs. Then the ice maker and back panel are removed. I used a heat gun and screwdriver to chip and melt the ice build up. If one had the luxury of having another refrigerator to move food in to you could just unplug the unit until the ice melts.

Just pulled out theold and squeezed in the new. I forced it and it went in.

Replaced ice bin complete with wheel. Easy fix and resonable.

Could not figure out why this was happening suddenly. Then remembered I had recently changed the lid to one I had stored for over two years in the garage. They had sent me a replacement lid when the unit was less than a year old because the origianl had a crack in the clear section. Noticed it seemed a little warped. Thought I would replace it to see if that solved the
problem.
We had to replace the side panel of the draawer because the warped lid had broken the peg off of one side. I didn't want that to happen again.
The new lid did the job....This company is the only one I will use in the future for my appliances. Very easy to find parts and the pricing was better.

Removed the old frame and removed the metal rod from the front of the old and slide it in to the new frame.
Then I took a piece from the old frame, measured the distance to the center of the two shelf brackets mounted inside in the rear of the refrigerator. Then I drilled two holes in the salvaged piece and mounted the piece as a support under the new frame using #8 sheet metal stews. This will prevent future breaks.

you need to take the deli drawer out, make sure your flat head screw driver is large enough for the head of the screw as screwing into the plastic is a bit difficult. Other than that there are 2 screws and its pretty easy.

watched diagnosis and repair videos online, assessed problem, order part and replaced ice maker. was not expecting to replace wiring harness but got it done and icemaker is working just fine.

They send you just the guts, the inner core of the icemaker, and don't include the back piece that has the motor to rotate the screw-drive dispenser and the blower. You get 2 wiring harnesses, and since no instructions come with, you get to figure out which one. The replacement has a few different plugs than the original and those competent can determine which without too much problem. One obstacle was the grounding screw which was inaccessible without removing another part which would have added greatly to the difficulty. I snipped off the old wire and the ring-terminal on the new one and joined the two with a wire clasp. Works like a charm. I had previously replaced the cycling thermostat and checked that the water valve solenoid was within the proper ohm boundaries-don't spend the money for the whole thing without trying those first! Mine must be an odd model because no YouTube videos showed the icemaker from this model.

Broken bottom drawer lid mount

Reviewed replacement instructions video on your website. Just followed the easy instructions to pop out old cover and pop in new cover. I would not have tried to replace it myself had I not seen your video. Super easy.

(1) Slide out appliance and remove power source. (2) Removed lower access cover on rear of refrigerator. (3) Disconnected plug to the condenser fan motor. (4) remove blades by pulling gently forward (5) remove mounting hardware holding the fan motor (3 screws) (6) motor is now free and new motor can be installed

It was a very simple operation and was done in no time.

Doing it myself saved me at least $100.00 or more.

I was very happy and satisfied with the part and how doing it myself saved me a lot of time and money.