58719149403 Kenmore Dishwasher - Instructions

Had trouble installing the new gasket at first. Fell inside the door, and would not stay in the groove intended for it. After watching the video on your website, learned is best to angle the gasket and work in slowly to the groove from one side. Much easier then

Simply pulled old gasket out with hand, and slid the new one in place!

Watching a YouTube video that was attached to an email, I was able to install my new dishwasher filter in no time without any tools. Thank you.

Replacement was simple.

Used pliers to pull out the old gasket. New gasket snapped into place. Notice where notches in the gasket are when the old one is removed, so the new one can be properly oriented. It was not necessary to remove the door.

I followed directions from a video on this site and written directions in order to make the repairs. Pulled out the old gasket from one end with pliers . I cleaned out the slot in the door of any food or dirt and replaced with the new gasket. It was a very easy and quick repair that allowed me to use my dishwasher quickly. Thanks for the help.

Removed front panel of door, to get to the screws that hold the door on the hinges. Removed door, pulled gasket with pliers from bottom of door, not easy to get out because of mineral deposits. Had to push quite hard to get new gasket in. Put every thing back together and no leaks. I live in Alaska and I tried to order the part through Sears and they wanted $18.95 for shipping for a $12.87 part. The part with PartSelect was $14.92 but only $6.95 for shipping. I ordered the part on a Tuesday and recevied it on that Friday. We in Alaska get very tired of companies thinking we live on another planet. Thank you PartSelect.

Removed front cover. No instructions so I removed all the screws. Only the bottom 2 need to be removed(1 on each side) then push cover up to unlatch. Remove 2 wires and 6 screws. Replace soap dish unit. reinstall screws and wires. Replace front cover. The hardest part is the front cover.

Removed the screws at the top which held it in , then I pulled it outside of it's shell, took it apart and took the drain part off, replaced with new drain part, put it back together the same way I took it off, pushed it back in, put the screws back in, tested it, and it worked. Ta Daaa!

At first I wasn't sure; I thought I had to buy the inner panel of the door. Considering that I have to minimize expenses I made it a point to tackle the problem myself. I unscrewed the outter panel off the dishwasher door and located the dispenser from inside of the inner door panel.

I unplugged the old dispenser,which was damaged, unscrewed it from the panel and removed it. I cleaned any and all debris, dirt and soap scum it had accumilated over the short years we've owned it.

Finally; after I prepared the new dispenser for installation, I placed it in position screwed it in and plugged it in, which was slightly tricky because it is pretty snug against the inside door panel. Once installed, I got my older son, 15, to help me screw in the outside panel of the door, and as he held it I screwed it on the the inside panel.

I tested it with no dishes inside by pouring just a little detergent in the new dispenser, starting the dishwasher and I stuck around in case there were any leaks or any other possible disaster that could occur.

This was exactly one week ago and all is still well. By the way, the person who took my order, I believe her name was Joann, was great. She talked to me making certain I had the right part, which I was unsure of since the diagram on your site was not quite clear. On top of that; I didn't pay for overnight service, yet my part was at my door the next day. I was amazed at the quick service and delivery. Thanks Joann!!!

Felipe,
Poughkeepsie, NY

Disconnected water and power. Two screws secured pump. Simply disconnect and reconnect. Perfectly quiet and operational. Great easy fix!!!

followed online video provided and it was a snap

I just had to buy a new cap and screw it in.

Followed instructions with parts.

i removed the bottom dish tray, Found the plastic gasket, gave a tug with my needle nose pliers and pulled it out. laid it on the door to make certain that i placed the new one in exactly as the old one came out.pushed it in and set the dishwasher to wash to check i had it in correctly. WALLA instant satisfaction.