58719149402 Kenmore Dishwasher - Instructions

Looseing up rack wheeles took out keepers slid in new rack put in keepers and tighten wheel nuts make sure there tight thats it easy a baby can do it.

Pull the old parts out put new ones in..Changed bottom door seal and door tub gasket. In about 20 minutes.

Easy as pie. I tokk the screws out that held the dishwasher to the counter top out. Then removed the screws holding the strike in place, inserted the new one, installed screws and then rescrewed the 2 screws backintothe countertop. Job done. All told 5 minutes.

Simply unscrewed the old. Replaced with the new.

used pliers to hook up spring according to repair video.5 mins to check for proper tension.

The first sensible thing to do is to find the circuit breaker for your dishwasher and switch it off so as not to short anything (or yourself) out. Next, remove the lower piece of metal bracket from beneath the door by unfastening the two sheet metal screws (a nut driver or a screwdriver will do the job), taking note as to how it comes off so as to facilitate replacement. Some will recommend loosening the screws at the top from beneath the counter and pulling the machine forward a bit to gain access to the sides but, if you have a small enough hand (as I do), you can just reach in there and and hook the spring into place. I didn't want to risk loosening any plumbing! You'll need a flashlight to see where the ends connect. And, if one spring is still intact, you can reference that to reassure yourself you've got it right. I was able to stretch the spring out by hand and hook the thing to that little plastic gadget that pivots when you open the door. That's it! Button her up! You're done!

After getting a totally incorrect length of hose from partselect.com . Went to local hardware store and bought hose for $3.00 vs $20.99 + $10 shipping!
Partselect sent replacement hose of 24 1/4” vs the original hose of 27”. Good luck getting any response from them once they have your money!

There were 4 zip ties holding old silverware basket on to bottom rack snip them, remove basket install new basket with zip ties both ends 2 more in middle about 1-2” apart. Try to install ties about 1/2 way up on basket so it doesn’t get top heavy.

on a U-TUBE repair sequence it showed removing the entire front panel of the door. With this Kenmore model the front panel is in two parts. The upper part where the controls and latch are is independent of the front panel so all I needed was to unscrew the upper panel, unscrew the latch, pull off the wires and reinstall by plugging in the wires, screwing the new latch to the door, reinstalling the panel to the door. It took about 15-20 minutes for the entire operation.

Replacing the door bottom gasket is a breeze, just grasp with a needle nose pliers and pull out. I positioned a small mirror inside the dishwasher so I could see where the gasket fit back in. I pushed the new gasket into the slot and ----done.
The springs require that the dishwasher be pulled out from its opening after removing the screws holding it into the cabinet at the top of the dishwasher. Replacing the springs is easy, just remove the old ones from the the bottom frame holes and the plastic holder and put the new ones on through the plastic holder and then into the frame. Push the dishwasher back into its opening, square it with the cabinet and reinstall the mounting screws.

cannot describe because not good at it however I just read what everyone else did and it was a piece of cake.

just slid the wheel on.

Just snapped the wheels on and attached the bracket to the existing part.

Grabbed edge of one end and pulled seal out and cleaned the area of water stains and etc. , Then pushed new seal into place. . . . .

Removed two screws on each side, lower half. Inside, removed six screws. Replaced the assembly and replaced all screws.
Not worth the fifty dollars for the part, just to have a door open at the right time to empty soap. Quite a hefty price to pay considering the price of the machine