This part is a replacement wheel assembly for your lower dishrack. The wheels on the dishrack allow it to roll in and out of the dishwasher efficiently. If one of your wheels is broken or warped, you ...
Looking for a way to fix that leaky Frigidaire dishwasher? Let's get it solved with this genuine OEM door seal. This part is key to creating a leak-proof barrier between your dishwasher's tub and door...
Experience the peace of mind that comes with a perfectly functioning dishwasher again. Introducing the Frigidaire Door Spring & Cable Assembly ? your trusted solution to those troubling sudden door dr...
This lower rack helps hold your dishes in place during the wash cycle. If your current rack is broken or doesn’t hold dishes well anymore, this replacement can help your dishwasher work like new. It’s...
Are you having trouble with your dishwasher's water flow? Perhaps it's time to consider this replacement part ? the Frigidaire Water Inlet Valve. Made specifically for specific models of Frigidaire di...
This dishwasher air brake and drain hose assembly is designed to safely remove wastewater from the appliance while preventing contamination from the household drain system. The included drain hose cha...
This door latch secures the door during operation to maintain safety and proper performance. A reliable latch prevents interruptions and leakage. Replacing a worn latch restores secure closure and confidence during use.
$173.54
In Stock
Questions And Answers for 58715423100A
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Shelley
May 23, 2025
The gasket says it is for a Frigidaire. Would this gasket work on my Kenmore dishwasher
For model number 58715423100A
Hello Shelley, thank you for contacting us. All the gaskets listed under your model are manufactured by Frigidaire, and they will work on your Kenmore dishwasher. We hope this information helps!
1 personfound this helpful.
Was this helpful?
Thank you for voting!
Hamid
January 14, 2020
I have a Kenmore dishwasher that is working well, however, the touchpad is working only on start, high temp and air dry.
For model number 58715423100A
Hi Hamid,
Thank you for your question. If there are only a few buttons working on the touchpad, try using hair dryer on low heat and press the buttons for a few minutes to see if you can get them to work. If this does not help, check the connections between the control panel with touchpad, part number PS3504485, and the electronic control board, part number PS2379414. If the connections are fine, you will need to replace the control panel with touchpad.
We hope this helps. Thank you and have a great day!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
Disconnect from power Unscrewed 4 phillips screws from top of outer door. Unscrewed 2 screws each siide of door. Lower outer door section drops away. Note wiring sequence on dispenser, then disconnect wires. Unscrew 6 screws on dispenser and lift dispenser out.
Place new dispenser in place (note orientation), ann fasten in place with screws, remembering to replace wire retainer on left lower screw. Reconnect wires to dispenser correctly. Slide lower outer door over tabs and secure with the 4 side screws. Ensure lower door is up under control panel and secure with the 4 top screws.
Fill dispenser with detergent, reconnect power and test run while enjoying a cup of tea in celebration of a job well done..
replacing dishrack was simply removing old and sliding new onto track. however, removing and reinstalling water dispenser blade mounted on bottom of existing rack to new rack required much more time and effort .I needed to use flat screwdriver to pry plastic clamps apart and then a pair of channel locks to release assembly from original rack. It took some effort to finally accomplish . I believe all models that use this replacement rack would have this same issue with the dispenser blade and instructions for re-installation should accompany the new rack or better yet, new blade should be included on rack for those not familiar with using tools.
