52150119 General Electric Washer - Instructions

removed 3 screws from the back. Then removed the little water line clamp. unplugged the 4 wires. took the new part. plugged it in. put on the water line clamp. put the 3 screws back on. put the hoses on the back again. turned on the water supply. and started washer.

Pulled top off and removed corner mounting plate then unscrewed mixing valve.replace wiring to valve and mount new valve in it's place .put back support and corn brace .then attached hoses and put back in service .work great for 20 plus yr machine.thanks tom

I took the back cover off of the washer, studied my next move and jumped in.Easy Lou-eezee!

Removed back cover. Opened top lid - slid putty knife under front lip to release latch (2). Removed old valve hose and clamps. Replaced with new valve hose and new clamps. No more leaking during fill.

Did some checking to make sure the filter, screen and hose were unobstructed. Turned off water at faucets, disconnected hoses and drainage hose. Unplugged machine and pulled out far enough to access back. Used nutdriver to remove 6-7 screws that held the back on, and then inlet valve plate. Removed clamp on outlet hose, then one by one removed wires, making sure to connect them to the same connections on new valve. Re-connected outlet hose and reversed procedure. Easy fix. Went ahead and replaced hoses while I had it out.

This was a very easy repair. First I unpluged the 120VAC power cord. Then I turned the water off. Next I opened the hose connections. Then I removed 3 screws from the back which exposed the Inlet Valve. I removed the old valve taking note of where the wires went. Then I installed the new one. It took less than 10 minutes!

removed old knob pushed on new nrw one locked on wifh key

Took off the backing and then the water inlet piece and just reverse the procedure when installing the new part. What really amazed me was the ease of ordering the part through this website. I found it, ordered it and in two days it was here!! Great website, you folks really know what your doing. My repair was under 25 dollars, how much would have I paid for a service tech to come out, don't even want to think about it !! I'm telling everyone I know about your website. THANKS AGAIN !!!!!

Very straight forward install. First removed the agitator itself by pulling straight up on it. Then removed the agitator coupling without the need of any tools just pull it straight off. Install new coupler and agitator.

An older gentleman neighbor needed help finding a part for his machine. We checked local parts stores to no avail. I researched the internet, found your site and ordered the part. My adult son put the part on in less than 15 minutes. Our neighbor was very happy. We will tell any one in our neighborhood to order parts here. We followed the part watching UPS. The part arrived at the exact day and time. It couldn't be easier.

quck delivery thanks. removed back panel and valve assembly. replace unit,and replaced panel. yep it works

its great and saved me lots of money enjoy my washer again

Turn off cold & hot water inlets. Detached water and drain hoses from Washer. Unplugged electricity.Removed back panel using nut driver/wrench would also work. Detached plate holding old valve and then old valve from plate. Held old valve in one hand, detached each electrical connection from old valve and attched to same location on new valve. Reinstalled and reconnected everything. Work like a charm. $20 bucks instead of a new washer. Point of fact: the valve contains the selinoids that regulate water flow. I did not know this and was trying to find "Selinoid" instead of inlet valve.

Replaced the water inlet valve. Your shipping was next day the best I have ever received. Thank You

Using the 1" putty, push in on the 2 clips holding the top of the washer. Lift top, exposing the top of tub. Remove old rubber seal from top edge of tub. To ease installation of new seal, stretch it over the edge of tub which tensions it, then start tucking the outer lip along the outside edge, tilting the seal towards the outside edge until the seal is completely in its groove all around. I had to hold down on the seal to keep it from rolling off while I lowered the top back down. When the lid is down, push hard to engage the 2 clips that lock it down.