41781102002 Kenmore Dryer - Instructions

Removed back of dryer with electric nut driver. Lots of screws. Removed old heating element to better access wires and thermostats. Removed baffle at end and transferred to new heater element. Transferred thermostats to new element, reconnected wiring in correct order. Installed new heater element in correct position using tab to locate. Replaced back of dryer. Reconnected dryer vent. Toughest part was squeezing out of space after reconnecting dryer vent. Unfortunately, too short for my weight.

The ice maker wouldn't fill with water. The maker itself appeared to operate but the tray would not fill. I ordered the part from PartSelect.com. The website allowed me to conveniently match a picture of the part with my part on the refrig. I ordered the part and it arrived in two days. I was impressed!

I turned the water to the ice maker off, unplugged the refrig. and pulled it out from the wall. I loosened and removed two screws with a nut-driver and unplug the wiring connection from the old part by simply pulling on it with my fingers. I then unscrewed the water connection from the old part using a set of pliers. The old part was then discarded. I connected the water and electrical and remounted the new part using the two screws. It was too easy!

1. Loosened the 3 screws inside of the drum
2. Removed the entire back of the dryer (lots of screws)
3. Removed the old vent (there are 2 screws at the bottom that hold it in)
4. Install new vent (put the screws back in)
5. Close up back and proceed to put all of the screws back

By undoing the single screw which holds the sensor in place, the old one falls off. To replace: simply pop the two wires on their connections (small metal studs on the back), slide clip/wire end of sensor in place and replace the screw. You are back in business! Very simple repair that a DIY can save a ton!

We followed a YouTube video and did the repair ourselves over an afternoon. We had one screw leftover (?) but everything went back together and now the dryer works like a dream! We bought a PartSelect part because we don't want to have to do this very often! ??

Removed screw and disconnect wires. Connect wires to new Moisture Sensor and slide clip to right side of dryer and tighten screw on left side.

Main problem was the bearing, replaced the belt and felt seal as well
The video instruction was very helpful
Was easy with basic mechanical aptitude
Dryer running great now
All parts from Partselect.com
Have ordered from them before and would order from them again

followed the instruction on you tube, the part was exact, there was nothing to guess, basically you take the whole front off of the dryer, that in itself is easy (follow instructions), once you get to the element, just plug and play. the worst part was a set screw in the back that did take some patience, but finally did get it in. I am not a mechanic in the least, trust me, if I can do it then anyone can. you will need regular Philips screw driver and one short one, really short, mine is about 2 inches in length, also I used manual one, allot of plastic, so I would not recommend electric drill or electric driver. also a good pair of plyers, but small not large.

Once we got the dryer out of the cramped where we could work on it, the project went a little quicker. I'd recommend using paper plates/bowls, that you label, to hold all the screws for each piece you remove off the back. It doesn't seem like it will be a lot, but we had at least 20-30 screws in 4-5 different sizes. Unlike someone else's install, we had to completely pull the white back panel off, as well as the main back cover, due to one screw holding the air duct from the inside of the dryer compartment (meaning we couldn't reach everything from the back). Getting this screw out was a challenge and seemed like a huge design flaw, but if you can't get to that screw, the old air duct isn't coming out. There are 2 other screws holding the air duct but they're easy to reach once the back panel is off.
Once that was taken out the process was straightforward, we just took our time reattaching everything step-by-step. Now our dryer works like new.

I had difficulty getting the old part out to get the new one in. I just about had to take the gram apart to get to everything.

Tight quarters but went well, fairly easy except for the far back screw that secures the element to back of dryer. Would have been easier if I removed drum but I didn’t want to disassemble that much. All is good and wife is ?? . If need help with disassemble Utube is your friend.

You must disconnect appliance from the gas, water and vent to access the back. Remove the top of the dryer which then allows you to remove the rear panel by removing all screws, You may also have to remove 2 electrical connections to get this panel off. Now you have access to the air duct. To remove the air duct there are 3 screws inside the dryer and 2 screws on the lower part of the air duct. One of the lower screws is facing toward the inside of the dryer and you will need a 12"+ screwdriver to be able to remove. Once you do all that install the new part and repeat steps in reverse.

Getting to the element and putting the machine back together, in my case, was the most difficult part. There are tons of youtube videos that can guide you through the removal and replacement better than I can. I recomend watching those videos and taking pictures of the old element prior to removing it. Also, I would put all the screws in separate ziplock bags with labels on them because every screw for my model was unique. I would also tape and label the electrical wires too.

I purchase one tube of heat resistant adhesive but I change both seals if you could afford to buy a second to I would recommend you do so the one tube just made it. For instructions on how to prepare the drum for installing new seals I went on YouTube

Fast and easy. Started by pulling out refrigerator and unplugging it. Water valve for ice maker was already turned off due to leaking. Disconnected old valve, detached old valve, reattached new valve and reconnected water lines. Bled the lines and turned back on. Make sure temp in freezer stays at recommended temps for ice making.